Re: overclocking kernel modules for PR1.2
 

I've took files of amandalam and modified them a bit , also removed 1.1ghz oc profile .

Installing procedure is same , copy usr and opt in the root of N9 then execute this command :

chmod +x /opt/overclock/*

Description of files :

1GHz default profile , smartreflex enabled
1.2GHz + smartreflex disabled
1.3GHz + smartreflex disabled (Better don't try this , it's pretty unstable)

Re: overclocking kernel modules for PR1.2
 

I think it depends on each Nokia N9, how each TI OMAP 3630 inside supports higher frequencies. Like overclocking the N900, some lucky users got 1,15 GHz, others only 950 MHz without problems.

Re: overclocking kernel modules for PR1.2
 

Yes , I've made that 1.3 file for people who want to try it . But I doubt there are phones that could run at 1.3 with no voltage increment .

By the way , has anyone tried other tweaks like governor , up treshold , etc ?

So far I've set up_treshold to 75 and , oc to 1200 and set min freq to 600mhz and of course disabled SR 1 and 2 . We can also tweak ignore_nice_loads , power_bias . :)

Re: overclocking kernel modules for PR1.2
 

Anyone able to help me with this, Im keen to try! Thanks!


I have aegisctl_pr1.2, opensh_1.00 & inception 0.1 installed.

Re: overclocking kernel modules for PR1.2
 

hmm... did you incept aegisctl when you installed it?

Edit: and did you incept opensh when that was installed too?
you also have to be using opensh instead of devel-su by typing "opensh" in the terminal at the start, yeah I know that's basic, just trying to cover all bases here.

There's also accli -i to check your credentials, and of course you have to be using opensh to get full privileges, installing them alone isn’t enough. I'm not fully sure of the intricate details of inception stuff mind you.

If the above get's you nowhere, I imagine it would be hard to remember if those packages were incepted so you should probably uninstall opensh and aegisctl then reinstall them making sure you follow the install instructions on the inception website to the letter, I believe the main thing is to incept those packages when they're being installed though.

Also itsnotabigtruck mentioned some inception related irc channels he tends to be on a few posts back, if anyone can figure out what's going wrong for ya it'll be him.

Re: overclocking kernel modules for PR1.2
 

As HansBliz said, the following steps should be followed strictly :

- to install Inception, opensh and aegisctl, see the Inception web page and copy the 3 .deb files to some directory and type :
$ devel-su
and type the password (rootme is the default one), go to same directory;
# dpkg -i inception_0.1_armel.deb
# pasiv
confirming with yes;
# incept opensh_1.00_armel.deb
and type the password (rootme is the default one);
# incept aegisctl_1.2_armel.deb
and type the password (rootme is the default one).

Re: overclocking kernel modules for PR1.2
 

I didnt "incept" opensh and aegisctl. I just did what 1st post says. DIdnt really read the INCEPTION website. Thanks guys, Ill have a play after work.

Re: overclocking kernel modules for PR1.2
 

got it working!! THANKS

Re: overclocking kernel modules for PR1.2
 

If I CBF Id write a clear How-To...

E: Going to try pushing my phones OC limit instead

Re: overclocking kernel modules for PR1.2
 

48 hours after i've set 1.2 frequency and no smart reflex , no reboot/glitch/freeze so far and battery life seems to be almost the same .

Any news about voltage control ?