maemo.org - Talk
Page 152 of 159 « First 142150151 152 153154 Last »
Show 40 post(s) from this thread on one page

maemo.org - Talk (https://talk.maemo.org/index.php)
-   Nokia N9 / N950 (https://talk.maemo.org/forumdisplay.php?f=51)
-   -   [HOWTO] Comprehensive Firmware Flashing Guide for N9 (https://talk.maemo.org/showthread.php?t=82693)

badpixel 2017-03-13 10:15
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
As other mentioned try full reflash.
You can also check dmesg for onenand errors. I have plenty of such, but it works stable.

Anatolian 2017-03-13 11:22
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
1 Attachment(s)
Nope ,
I have reflashed it Like in the commands of Nıeldk

( full) and the storage turn to normal (15.76 GB) but stıll boot

error ( (weırd texts, karnel ınformatıon when bootıng) cam not

workıng stable, front led open, back led red Light open :),

But more stable THAN yesterday :)

I have run the top in the xtermınal to sen what cpu busy

Nothıng understand ,

Something weırd here in the pıcture

aspergerguy 2017-03-13 20:28
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
If front LED was continually flashing and red LED was on, I would have wondered whether R & D mode had been enabled at some point. Does entering following in flasher make any difference to boot?
Code:
--enable-rd-mode --set-rd-flags=no-lifeguard-reset
To disable R & D mode use
Code:
--disable-rd-mode

Anatolian 2017-03-14 10:00
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
Thank you mate solve, R D mode was open Like Said..

Thanks all guys.

andreasole 2017-03-29 11:06
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
Please someone explain what is the problem??

@andreasole:~/Downloads$ sudo flasher -F main.bin -F emmc.bin -f
flasher 3.12.1 (Oct 5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 001, device address 021.
Device identifier: 357923047555604 (SN: N/A)
Found device RM-696, hardware revision 1603
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_001
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 3492 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 001, device address 022.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 94 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 2883 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 584 kB/s]
[_] rootfs [writing 7 % 89088 / 1170282 kB 2507 kB/s]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
Raw data transfer failed: Resource temporarily unavailable

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 2883 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 584 kB/s]
[f] rootfs [writing 0 % 89088 / 1170282 kB 2507 kB/s]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
========================================

ERROR: Failed to flash images
andreasole@andreasole:~/Downloads$ sudo flasher -F main.bin -F emmc.bin -f --no-preserve
flasher 3.12.1 (Oct 5 2011) Harmattan
Warning: --no-preserve is not recommended, instead use erase commands
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 001, device address 022.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 95 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[ ] cmt-2nd [pending 0 % 0 / 0 kB NA ]
[ ] cmt-algo [pending 0 % 0 / 0 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[ ] kernel [pending 0 % 0 / 0 kB NA ]
[ ] rootfs [pending 0 % 0 / 0 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3198 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 879 kB/s]
[f] rootfs [pending 0 % 0 / 0 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
Update content failed to verify against cert: SW certificate not updated
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not remove mount directory /tmp/sudmmchggbfl/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images
andreasole@andreasole:~/Downloads$ sudo flasher -f -F main.bin --erase-user-data=secure -F emmc.bin
flasher 3.12.1 (Oct 5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 001, device address 022.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8

Battery level 95 %, continuing.
Erasing, this may take a while.
Erase done.
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 98 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[_] cmt-mcusw [init 16 % 1024 / 6050 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 624 kB/s]
[_] rootfs [finishing 100 % 6144 / 1170282 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3205 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 624 kB/s]
[f] rootfs [finishing 0 % 7168 / 1170282 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
Update content failed to verify against cert: SW certificate not updated
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not remove mount directory /tmp/sudmmcfBCB8F/mnt: No such file or directory
[Pipe 5] Finishing in error state with status 1
========================================

ERROR: Failed to flash images
andreasole@andreasole:~/Downloads$ sudo flasher -F main.bin -F emmc.bin -f
[sudo] password for andreasole:
flasher 3.12.1 (Oct 5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 001, device address 023.
Device identifier: 357923047555604 (SN: N/A)
Found device RM-696, hardware revision 1603
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_001
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 4171 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 001, device address 024.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 92 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 2946 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 541 kB/s]
[f] rootfs [writing 0 % 408576 / 1170282 kB 3087 kB/s]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
========================================

ERROR: Failed to flash images
andreasole@andreasole:~/Downloads$ sudo flasher -i
flasher 3.12.1 (Oct 5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 001, device address 024.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Success
andreasole@andreasole:~/Downloads$ sudo flasher -F main.bin -F emmc.bin -f --no-preserve
flasher 3.12.1 (Oct 5 2011) Harmattan
Warning: --no-preserve is not recommended, instead use erase commands
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 001, device address 024.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 93 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[ ] cmt-2nd [pending 0 % 0 / 0 kB NA ]
[ ] cmt-algo [pending 0 % 0 / 0 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[ ] kernel [pending 0 % 0 / 0 kB NA ]
[ ] rootfs [pending 0 % 0 / 0 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3200 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 885 kB/s]
[f] rootfs [pending 0 % 0 / 0 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
Update content failed to verify against cert: SW certificate not updated
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not remove mount directory /tmp/sudmmcwADmzO/mnt: No such file or directory
[Pipe 5] Finishing in error state with status 1
========================================

ERROR: Failed to flash images

andreasole 2017-03-29 11:32
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
And after this command i get this

@andreasole:~/Downloads$ sudo flasher -f -F main.bin --erase-user-data=secure -F emmc.bin --erase-mmc=secure
flasher 3.12.1 (Oct 5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 001, device address 024.
Device identifier: 357923047555604 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Warning: user data may reside on MMC. In that case the MMC is unnecessarily erased twice.

Battery level 94 %, continuing.
Erasing, this may take a while.
Erase done.

Battery level 98 %, continuing.
Erasing, this may take a while.
Erase done.
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 97 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 739 kB/s]
[_] rootfs [finishing 100 % 7168 / 1170282 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3174 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 739 kB/s]
[f] rootfs [finishing 0 % 8192 / 1170282 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
Update content failed to verify against cert: SW certificate not updated
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not remove mount directory /tmp/sudmmctHBhqI/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images
andreasole@andreasole:~/Downloads$

aspergerguy 2017-03-29 14:16
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
Unfortunately looks like HW issue with flash memory, see here for similar issue: http://talk.maemo.org/showthread.php?t=94575

andreasole 2017-03-29 17:14
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
Quote:
Originally Posted by aspergerguy (Post 1526112)
Unfortunately looks like HW issue with flash memory, see here for similar issue: http://talk.maemo.org/showthread.php?t=94575
Finally after this command

flasher -F main.bin -F emmc.bin -f

It flash only the main.bin so the phone starts again , now my question is that i was doing this to install sailfis so i continue from from the STEP 3 flash Openmode Kernel and continue or i need also flash emmc.bin?

arct 2017-09-17 07:58
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
I had nokia with variant 232 I flashed it with 341 which is of poland.
Now it is asking me for unlock code.But I live in India and here we dont have arrier for n9.What should i do.

Should i flash it with 009 variant??

nieldk 2017-09-17 12:04
Re: [HOWTO] Comprehensive Firmware Flashing Guide for N9
 
Quote:
Originally Posted by arct (Post 1534512)
I had nokia with variant 232 I flashed it with 341 which is of poland.
Now it is asking me for unlock code.But I live in India and here we dont have arrier for n9.What should i do.

Should i flash it with 009 variant??
Unlock code? Are you sure it’s network locked?
If it’s phone lock, you might try “12345”


All times are GMT. The time now is 15:00.
Page 152 of 159 « First 142150151 152 153154 Last »
Show 40 post(s) from this thread on one page

vBulletin® Version 3.8.8