Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

freq 1300 voltage 1375000 ok stable
freq 1315 voltage 1375000 ok stable
freq 1330 voltage 1375000 ok stable
freq 1350 voltage 1375000 ok stable
freq 1360 voltage 1375000 ok stable
freq 1370 voltage 1375000 ok stable
freq 1380 voltage 1375000 ok stable


freq 1385 voltage 1400000 ok stable and fasterrrrrrrrrrr turbo
all above is with sr off all aplications on and 48 hours hard testing batery ok but a litle hot after hours testing temperature of conky max 40 celciu after hours testing

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Anyone else got 'failed to execute loader?' I have installed inception, seemed to install fine?

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

you must enable the inception not only install
after install the inception deb file do this open terminal and type comand
devel-su -c /usr/sbin/pasiv

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Thanks:) I did this before, is it necessary to do this every time on reboot?
C

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

no you dont but every time reboot you take the original setings you must change again and optimize your setings not inception from the optimizer loader if you dont reboot even the aplication is closed the setings are ok

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Hey creamy,can I Become the beta tester? I'm sorry,I can't pm...it says I do not have the privilege.lol

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

hmm even with a successful inception enabling, opening OppUI still gives me the 'failed to execute loader' in status. Is there anything else I could have done wrong?
(Im on PR1.2 and using the latest files at the beginning of this thread).

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

open terminal
devel-su then enter
pass = default rootme and is hiden then enter
(put the armel.deb files at MyDocs and hit)first
/usr/sbin/incept /home/user/MyDocs/opptimizer_1.5.3_armel.deb enter and then /usr/sbin/incept /home/user/MyDocs/opptimizer-ui_1.0.1_armel.deb enter and done thats it but dont forget put the .deb files at MyDocs folder and after the incept to /home leave space incept space /home

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

and video step by step how to install conky http://www.youtube.com/watch?v=lsJ0ieCX7xo

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

im just clik on the deb file and conky installed :D

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

I had been installing direct via filebrowser. hmm ok so I started form the beginning, enabled incept.

Then I did exactly

open terminal
devel-su then enter
pass = default rootme and is hiden then enter
(put the armel.deb files at MyDocs and hit)first
/usr/sbin/incept /home/user/MyDocs/opptimizer_1.5.3_armel.deb enter

and get incept:No such file or directory

Is there something up with my incept installation?? (Thanks do much for the help)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

yes after incept leave space and then /home/user/bla bla bla
and go to applications and check if installed inception installer and inception sec policy

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

enjoying.. :D:D

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Dear Creamy Goodness,

have you sent the new test version yet?

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

No, i'll send it within 12 hours i think.
I was going to send it 12 horus ago but I found another bug I caused to fix first :(

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

i can wait, you rock!!!

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

freq 1390
voltage 1400000
sr off
testing 24 hours very hard stable and faster

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

BREAKING NEWS:
TMO user 'besttt' has been pronounced dead from his N9 exploding as he stressed the CPU to its limits using Opptimizer!

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

it works perfect my friend stable fast low temperature
at relax time 27 celciu temperature medium use 32 celciu temperature hard use all aplication open for 4 hours 40 celciu temperature pasing the stress test not reboot at all stable very fast

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

1,375ghz , 13750000v sr on, my everydayuse, :)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

what about battery life ?

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

almost same, use fastern9 and its will be cool, :)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

1200Mhz @ 1287500 testing began SR on
lower voltages failed

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

lower voltage is more dangerous than higher higher voltage its just reboot or failed lower voltage makes cpu lost synchronization if the combination works the cpu if overheating its just lower the frequency for a moment ant thats it

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

different device different experience, just be careful, dont push your device too hard, do it at your own risk

here is mine https://fbcdn-photos-a.akamaihd.net/...761_n.jpg?dl=1

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

i think the 64gb version is more powerfull and stronger

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

one device already died, and thats 64gb version, :D

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

thats it my settings

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

sr off, be careful, but thats ur choice, :)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

my sr is off too, bec i cant stable at 1200 ghz ever in 1.375v
now testing with sr off with 1.3v, seem stable until now

my device only stable with sr on at 1150 ghz..

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

sr off means push so hard on ur chip, cmiiw, remember that every device is different, if ur lucky enough you can get higher with sr on, :)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

I'm running stable for almost two weeks, without any problems what so ever on 137000 voltage and on 1375 MHz, with smartreflex on.
Also my girlfriend at the same time....

Arie seems to had a problems already at low overclock and voltage at the begining. Maybe he had bad chip? IT's worth to try and send it to repair under the warranty ("I don't know what happened, but it was lately quite warm on the back").

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Any reason to think that?

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

failed did not last one hour
REtesting with SR on same frequency and voltage
seeing the results i also think 64gb are more cappable than 16gb
mine is 16

With Sr on also failed :confused:time to raise the voltage...

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

He can't really send it anywhere because he bought it in USA. No warranty. :( But he likes his n950 :)

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

mine is 16gb version, cyan one, @1,375ghz and 1375000v now, any idea?

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

Last results , tests , conclusions , on my n9 :

1350mhz , 1.325v , sr off - Rock solid , I think this is the lowest voltage for 1350mhz .

1350mhz , 1.325v , sr on - Unstable , rebooted after 3 minutes
1350mhz , 1.3125 , sr off - Pretty stable but I got a reboot after ~12 hours .

So far I found perfect voltage for 1350mhz , but I don't think 50mhz makes a visible difference so I will try with 1300mhz and lower voltages .

I feel sorry for the guy who fried his chip , I also stopped trying high voltages and frequencies that my device can not handle . I've tried max 1450000v via xterminal but is still very laggy and unusuable after 1370mhz . N9 is such a "fragile" device , N900 is like a rock , there are very few permanently bricked N900s reported .

Re: overclocking kernel modules + UI for PR1.2 [ko v1.5.3] [ui v1.0.1]
 

so far so good gonna go the same freequency you have with the same voltage and will feedback
wish me luck;)