Re: Cold Flashing
 

Hey everyone,

i am having a little problem cold flashing my N900 (my operation system is Ubuntu 13.04).

First of all i am not able to find out which HW revision my device belongs to so i tried some of the HW revisions found here but with every revision i tried i was only able to complete the first step with an output similar to the one in the wiki.
When i try to flash with the --flash-only=nolo option i am only getting the "Suitable USB device not found, waiting." output.
This now leaves me with some questions i am hoping someone will be able to answer :)

Is the HW revision by any chance printed on the motherboard or somewhere else (i couldn't find anything via google or board search).

After the special OMAP Program was succesfully send i always took out the battery typed in the next command and slid the battery back in.
Is this the correct way or did i do something wrong here?

Best regards
Fottes

Re: Cold Flashing
 

@Fottes:

HW revision is not printed anywehere. But all HW revisions 21xx and 22xx are using same 2nd and NOLO images. So you can assume that you have one frequently used hw.

Cold flashing is needed only if bootloader was damaged, so when this command not working:

$ flasher-3.5 -i

How to cold flash, see post #9. If you really do not know your hw rev. use 2101. You cannot do anything with non working device with damaged bootloader...

Re: Cold Flashing
 

@pali
First of all thanks for the fast answer.

$ flasher-3.5 -i wasnt working this is why i tried cold flashing :)
I was already using the commands you refered me to, but still wasn't able to either flash with --flash-only=nolo nor do a normal flash.
Also my N900 doesn't enter flashing mode afterwards, if i plug it in again while holding u.
This is why i was asking if im missing something, after i have completed your steps (like waiting for the Phone to reboot or something).

Btw battery is fully charged using a second N900.

P.S. i just noticed that this thread was in the General Section even if it would better fit into the N900 Section sorry for posting in it.

Re: Cold Flashing
 

check if you are using usb 1.0 or 1.1 ports. I had problems with usb 2.0 for cold flashing (and my usb 3.0 ports not working with flasher-3.5)

next make sure you are using 32 bit version of some linux distribution (some 64 bit has problem with 32 bit version of userspace)

and also provide output of your flasher commands. before cold flashing phone must be (fully) charged and turned off.

Re: Cold Flashing
 

I'm using USB 2.0 ports (but i will try to find someone who still has USB 1.0 or 1.1 ports to also give those a try).
The Ubuntu version im using is 32bit.
Battery is fully charged, phone turned off, battery removed.
After I plugged in the USB cable, I slide in the battery with the keyboard open.

Output of first command:
Output of second command which doesn't find a suitable USB device

Re: Cold Flashing
 

Output of first command is OK, now you should have working NOLO in n900 nand. After first command do you see NOKIA logo & usb icon on n900 screen?

Also please provide dmesg output *after* you cold flashed device

Re: Cold Flashing
 

Neither the Nokia logo nor the USB icon do appear on the screen.
Output of dmesg (hope i quoted the right part)

Re: Cold Flashing
 

Cold flash working without problem (from your output) and if you did not saw NOKIA logo after cold flash you have 1) bad/uncompatible USB cable/port/computer for normal flashing or 2) your n900 is broken in HW and cannot start NOLO.

Try another usb cable, usb port and computer. I have 1) problems with my usb some 2.0 and all 3.0 ports. Only one combo usb2.0/eSATA port working fine for flashing. But any other usb device which I have working fine with any my usb ports...

Re: Cold Flashing
 

This is id is for N900 Cold Flashing mode, not NOLO.

Re: Cold Flashing
 

I will try another computer and report back.
Thank you for your help and patience till now :)

EDIT:

I tried 2 different computers (though i couldn't find one with USB 1.0/1.1 ports) but still couldn't get it to work.

Since the phone was dead after i went running with it (guess what i won't do with my spare one), i bought some isopropyl to clean it and gave it another try.
It worked and i was able to pull my data off it.

Thanks again for your help pali :)