maemo.org - Talk
Page 26 of 33 « First 162425 26 2728 Last »
Show 40 post(s) from this thread on one page

maemo.org - Talk (https://talk.maemo.org/index.php)
-   Nokia N9 / N950 (https://talk.maemo.org/forumdisplay.php?f=51)
-   -   overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.7] (https://talk.maemo.org/showthread.php?t=83357)

Creamy Goodness 2012-07-17 04:43
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I think it worked, thanks for the hint wook. I removed the kernel version from everywhere except the dependencies where I specifically said either one is fine, so it should be good to go on n9/n950 pr1.2/1.3. I updated the 1.5.4 version again since changing the # is a pain :)

Timpaxi 2012-07-17 08:27
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I have a problem again.. When i'm trying to incept those files it says not found..? And files really are in that folder what i'm trying to incept..


Solved! I'm an idiot.. Didn't remember to install inception after my last reflash.. :D

emam damon 2012-07-17 08:41
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
is it works fine on v 1.3 now?

Timpaxi 2012-07-17 09:06
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by emam damon (Post 1238603)
is it works fine on v 1.3 now?
Yes it works. Well, i just installed it but anyway it works. :)

besttt 2012-07-17 09:07
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by emam damon (Post 1238603)
is it works fine on v 1.3 now?
yes it works fine

emam damon 2012-07-17 09:19
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Thank you very much mates.
i'm newbe here,would you please tell me how much is the highest stable value for cpu and voltage for v1.3?

godofwar424 2012-07-17 09:57
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by emam damon (Post 1238619)
Thank you very much mates.
i'm newbe here,would you please tell me how much is the highest stable value for cpu and voltage for v1.3?
Don't be lazy! read through the first ten pages of the thread and have a look!!

If you need to ask these questions, maybe you shouldn't be doing something that could potentially brick your device and void your warranty!

emam damon 2012-07-17 10:07
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by godofwar424 (Post 1238632)
Don't be lazy! read through the first ten pages of the thread and have a look!!

If you need to ask these questions, maybe you shouldn't be doing something that could potentially brick your device and void your warranty!
hey mate i have seen those but i think all of those refer to v1.2.i want to know what is the best value for v1.3?

wook_sf 2012-07-17 10:46
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
great to know that it works Creamy, btw, how to force you to make down clock ocable? :D

MoritzJT 2012-07-17 12:01
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by emam damon (Post 1238635)
hey mate i have seen those but i think all of those refer to v1.2.i want to know what is the best value for v1.3?
The same as on 1.2 as your hardware has not changed ;-)

However on PR1.2 I was able to apply my changes without any testing cycle. The same values now give me an error but apply fine after 1000.

Any idea?

Cheers

Creamy Goodness 2012-07-17 15:51
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by MoritzJT (Post 1238677)
The same as on 1.2 as your hardware has not changed ;-)

However on PR1.2 I was able to apply my changes without any testing cycle. The same values now give me an error but apply fine after 1000.

Any idea?

Cheers
Probably a bug, I'll have to look at it to see why. Mine is doing that too...

Quote:
Originally Posted by wook_sf (Post 1238649)
great to know that it works Creamy, btw, how to force you to make down clock ocable? :D
Arie keeps asking too. There might be some way to disable the 1ghz opp without this tool, then you would be downclocked to 800.

wook_sf 2012-07-17 19:02
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1238788)
Arie keeps asking too. There might be some way to disable the 1ghz opp without this tool, then you would be downclocked to 800.
no, i am talking about lowclock not highclock
i think i have issues when waking phone, it starts to chock :D really it behaves like that
seems like it's jumping from 300mHz to 900mHz then to 350mHz then to 950mHz then to 400mHz then to 900mHz then to 600mHz then to real speed...

Arie 2012-07-17 19:05
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by wook_sf (Post 1238902)
no, i am talking about lowclock not highclock
i think i have issues when waking phone, it starts to chock :D really it behaves like that
seems like it's jumping from 300mHz to 900mHz then to 350mHz then to 950mHz then to 400mHz then to 900mHz then to 600mHz then to real speed...
I want it to sit at 300mhz when the screen is off and then hit say 1150(what im at now) when the screen is on, that would save battery and make the N9 pretty much the same as the droid 2's in that regard.

wook_sf 2012-07-17 19:32
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Arie (Post 1238903)
I want it to sit at 300mhz when the screen is off and then hit say 1150(what im at now) when the screen is on, that would save battery and make the N9 pretty much the same as the droid 2's in that regard.
yes, but it is scalable, not fixed, so...it will be hard to sit exactly on 300...that's what makes choking though, anyhow, i am not quite sure, but this sounds like solution to me, clock sleep mode to 500mHz and it would wake easier, it's horrible when it's waking with phonecall...

Rogatti 2012-07-18 00:19
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
-
-
I think overclocking only compensates for certain tasks ...
-
in 80% of my time using the N9 overclock only consume battery ..fact

jleholeho 2012-07-18 00:49
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I wouldn't say that...
only with OC I'm experiencing real, no laggy N9...
FasterN9 script made literally nothing to my N9, except for some strange mishaps like Messages app opening in intolerable 4 or 5 seconds, toggles in status bar working incorrectly, etc...so I got rid of it
now I continue to use my N9 @1.3GHz as with previous core version and it's all good...

Ch.Saqib 2012-07-18 19:29
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Amazing people really live in this world and they are here in this community. You are one of them Creamy Goodness.
Thanks a lot for making it possible on updated N9.
I have successfully overclocked my N9 to 1.3GHZ again.

RafaelVlmendes 2012-07-18 21:39
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Hi Creamy Goodness
The downloads no work. Can fix please. Thank very much.

Creamy Goodness 2012-07-18 22:51
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
They should work, it's my server and it's not offline right now. It could have been some temporary problem, please try again.

RafaelVlmendes 2012-07-18 23:52
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1239493)
They should work, it's my server and it's not offline right now. It could have been some temporary problem, please try again.
Thank.
100% working.
Creamy Goodness please visit the page Nokiatividade from Brazilian.
Iam public to site too. Visit and coment.

http://www.nokiatividade.com/n9vidad...-3-ate-14-ghz/

Creamy Goodness 2012-07-19 00:21
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Cool, it's your site? Seems pretty popular.

wook_sf 2012-07-19 00:28
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1239524)
Cool, it's your site? Seems pretty popular.
just if it would be in english :)

Rogatti 2012-07-19 01:09
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by wook_sf (Post 1239526)
just if it would be in english :)
-
-
as they say .. the king is naked ... and he still thinks the sun is ...:p

Ch.Saqib 2012-07-19 15:48
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Unfortunately my N9 is not as much smooth after overclocking as it was in PR 1.2 after overclocking. In both cases I have overclocked it @1.3Ghz. Anyone else feeling the same or it is just me?

thedead1440 2012-07-19 15:54
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
overclocking is a very subjective issue based on your chip and preferences. Its best to do trial and step at different frequencies to get your own optimal frequency instead of asking others for their opinions as there is a strong possibility that the chip batches differ.

Creamy Goodness 2012-07-19 16:31
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Ch.Saqib (Post 1239836)
Unfortunately my N9 is not as much smooth after overclocking as it was in PR 1.2 after overclocking. In both cases I have overclocked it @1.3Ghz. Anyone else feeling the same or it is just me?
You can try running some benchmarks if you want to make sure the overclocking still works, I never tested to be honest.

Ch.Saqib 2012-07-19 17:38
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1239855)
You can try running some benchmarks if you want to make sure the overclocking still works, I never tested to be honest.
Sorry to disturb you again. Can you tell me some benchmarks which I can run for the tests plz?

Ch.Saqib 2012-07-19 17:40
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by thedead1440 (Post 1239838)
overclocking is a very subjective issue based on your chip and preferences. Its best to do trial and step at different frequencies to get your own optimal frequency instead of asking others for their opinions as there is a strong possibility that the chip batches differ.
I think it is a good idea. I will surely try this out. Thanks

wook_sf 2012-07-19 18:02
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Rogatti (Post 1239539)
-
-
as they say .. the king is naked ... and he still thinks the sun is ...:p
sun indeed is, i am not sure about king :P :D

itsnotabigtruck 2012-07-19 18:16
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.3] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1238531)
Cool, okay, well I had to break the compatibility with PR 1.2 because I'm not smart enough to have the kernel modules install in the correct folder depending on whichever kernel you have. The only problem with that is if you are stuck on PR 1.2 for some reason you're gonna get the message popping up saying there's a new version but you won't be able to install it.
I just overwrote the file on my server again with another that should have the version string fixed internally too.
If you didn't sort this out already, I'd strongly suggest simply installing the module files twice - once into each kernel module directory. It's important that it not break during an upgrade from PR1.2 to PR1.3, which is what will happen if you install into only one directory.

The best approach IMO would be to install into one of the version directories, then make a hard link using ln in the postinst script before you depmod. Make sure to delete the hard link using rm in the postrm script, again before depmod. That way, only one copy of the files takes up space, but it works no matter what.

Of course, going PR1.3-only is a legitimate option - just make sure the dependencies are set up so that it can't be installed on PR1.2.

Creamy Goodness 2012-07-19 21:10
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Yeah geez I didn't think of that problem, in the mean time anyone that upgrades the OS should reinstall this package afterwards because the modules will be in the old folder and modprobe won't find them anymore.

Dragoss91 2012-07-20 14:52
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I have the same problem after Kernel 1.5.0 . With 1.5.0 I've used my device at 1300Mhz and 1.3v stable for more than a month . Now with these new versions nothing seems to work like before , the 1300mhz now needs more than 1,325v because it's freaky unstable , phone crashes in max 3 minutes even after 16000 iterations . It's a software problem I'm sure about that , my phone was able to run 1300Mhz at 1300000uv for months with 0 crashes or bugs .

Please tell me how could I fix this ? or how could I trick the OppUI to get the 1.5.0 version instead 1.5.4 . I've tried to replace .ko files in /lib/modules/current/ but it wasn't recognized in OppUI , everything was Unknown . :(

Creamy Goodness 2012-07-20 15:49
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
if you want them to be loaded automatically you need to use the installer for whichever version you want, not just copy the modules.
The md5 or sha-1 hash is inserted somewhere during the install to authorize them, the loader doesn't do anything like aegisctl -k on each boot so it can't load them otherwise.

simonizer 2012-07-21 08:37
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I'm having problems with SmartReflex.

Installed via Open Kernel. Set at 800 MHz @ 1100000 voltage. SmartReflex disabled.
Works fine so far.
But if i try it with SmartReflex enabled I only get a reboot and setting aren't applied. Not working.

Anyone else expierenced that kind of issue so far?

Dragoss91 2012-07-21 09:05
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1240351)
if you want them to be loaded automatically you need to use the installer for whichever version you want, not just copy the modules.
The md5 or sha-1 hash is inserted somewhere during the install to authorize them, the loader doesn't do anything like aegisctl -k on each boot so it can't load them otherwise.
Finally I found out the source of this problem . When you disable smartreflex with OppUI , only SR1 gets disabled , SR2 remains untouched (enabled) and is causing crashes . I had to disable it manually and so far my device is rock solid .

alexporta 2012-07-23 15:44
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Hi to all, I''ve installed all the packages but, when I start the program and try to modify the clock and the voltage nothing happens (no test and nothing remain in memory)

Creamy Goodness 2012-07-23 16:36
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Dragoss91 (Post 1240677)
Finally I found out the source of this problem . When you disable smartreflex with OppUI , only SR1 gets disabled , SR2 remains untouched (enabled) and is causing crashes . I had to disable it manually and so far my device is rock solid .
I left the other one on because it's supposed to be for the graphics, not cpu.

Dragoss91 2012-07-24 12:22
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
Quote:
Originally Posted by Creamy Goodness (Post 1241742)
I left the other one on because it's supposed to be for the graphics, not cpu.
Yeah , but it makes my life harder , so please ... :D:D:D


If I enable Apply on startup and reboot my device it boots twice due to SR2 activation and crash within 5 seconds , so everytime I have to turn it off manually with redak editor or winscp . And running stable with SR2 on requires +37500uv , a bit too much for 1.3Ghz .

Dragoss91 2012-07-25 10:32
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
I want to make some executable scripts with icons for disabling sr2 and other tweaks but with these updates of inception , aegisctl , I can not run them anymore on phone but with putty I can use ariadne sh "script" and it runs well .

Here are my scripts , please tell me if I did something wrong .

DSR
Code:
echo 0 > /sys/power/sr_vdd2_autocomp
echo 75 > /sys/devices/system/cpu/cpufreq/ondemand/up_threshold
echo 150000 > /sys/devices/system/cpu/cpufreq/ondemand/sampling_rate
ocDSR
Code:
ariadne sh "/opt/overclock/DSR"
DSR.desktop
Code:
[Desktop Entry]
Encoding=UTF-8
Version=0.1
Type=Application
Name=DisableSR
Exec=/opt/overclock/ocDSR
Icon=/usr/share/themes/blanco/meegotouch/icons/icon-m-bootloader-warning.png
Both ocDSR and DSR files are located in /opt/overclock/ and the .desktop file in /usr/share/applications . :confused:

Creamy Goodness 2012-08-01 06:57
Re: overclocking kernel modules + UI for PR1.3 [ko v1.5.4] [ui v1.2.5]
 
okay, I tried to fix 3 annoying bugs for now, can anyone test?

opptimizer-ui (1.2.6) unstable; urgency=low
* Fixed bug preventing 15k iterations to unlock the apply on startup option
* Fixed bug where crashes flag is not cleared when doing test of higher frequency at same voltage
* Fixed bug where 0 iteration test fails


All times are GMT. The time now is 05:56.
Page 26 of 33 « First 162425 26 2728 Last »
Show 40 post(s) from this thread on one page

vBulletin® Version 3.8.8