![]() |
[SOLVED]Problem in Flashing N900. Help needed Urgently.
Hi. last night i tried to flash my phone, it flashes kernel without any problem but when i try to flash eMMC. i tried many times but still no success. i have already tried flashing at my home pc in which Windows 7 32 bit is installed and there it completed without any error. but in my laptop which has windows xp SP 2 each time gives the same error. can anybody help me regarding to solve this issue. and by the way i have also installed Nokia Pc Suite.
|
Re: Problem in Flashing N900. Help needed Urgently.
Remember: eMMC (Vanilla) first, then rootfs (FIASCO), without rebooting in between.
Don't worry about the PC Suite. Go through the Wiki and post back with where you get stuck. If using windows, use XP not 7. |
Re: Problem in Flashing N900. Help needed Urgently.
Quote:
|
Re: Problem in Flashing N900. Help needed Urgently.
First try to flash with RX-51_xxxxx_ARM.bin
and then flash the RX-51_2009SE_1.2009.41-1.VANILLA_PR_EMMC_MR0_ARM.bin and again flash with RX-51_xxxxx_ARM.bin This will make ur N900 new and error free... I usually got error while flashing EMMC , so tht i am doing this.. and so far i got success in this ;) |
Re: Problem in Flashing N900. Help needed Urgently.
Not sure how it works in windows but I'm sure its not a good idea to install drivers for flashing mode. If you install drivers whilst flasher is doing its job or prior to flasher doing its job, you end up interfering with the entire operation of flashing.
My best bet is to disable the N900 PC-Suite drivers from even interfering in the first place, surely under control panel > System > device manager > hardware drivers (or something like that) can give you access to temporarily disabling the drivers. Also when you see that the flasher says `Booting device into flash mode', did you device restart? My best bet would be to temporarily boot into linux (on your desktop/pc) and use linux flasher from there. |
Re: Problem in Flashing N900. Help needed Urgently.
The device should be off when you plug it in (as per instructions) and so long as the Nokia cable drivers are installed, there's no problem and PC Suite won't try to initiate.
Things to look at: 1. I think there might be a problem with your directories (in windows). Try placing everything in the top directory of a drive (e.g. c:\) so the strings you need to enter are really short - I believe it needs full file paths. 2. Make sure you're using the most recent versions of the firmware (PR1.3 and similarly dated eMMC image). |
Re: Problem in Flashing N900. Help needed Urgently.
flashed my phone successfully using my cousins pc which is running on windows xp Service Pack 3. i think main problem is flasher needs service pack 3 to flash device correctly. Thanks everyone for helping me and taking time to solve my problem.
|
Re: Problem in Flashing N900. Help needed Urgently.
I got this msg when trying to flash my N900 and now my phone totally died. Can somebody help me :(
Image 'mmc', size 241163 kB Version RX-51_2009SE_1.2009.41-1.VANILLA Suitable USB device not found, waiting. USB device found found at bus bus-0, device address \\.\libusb0-0001--0x0421-0x0 105. Found device RX-51, hardware revision 2101 NOLO version 1.4.14 Version of 'sw-release': <no version> Booting device into flash mode. Suitable USB device not found, waiting. |
Re: Problem in Flashing N900. Help needed Urgently.
Quote:
|
Re: Problem in Flashing N900. Help needed Urgently.
I have a big problem. My phone does not start up and when i try to flash it the flasher shows %m and nothing happens
|
Re: Problem in Flashing N900. Help needed Urgently.
Quote:
insyaallah ur phone will be fine..... |
Re: Problem in Flashing N900. Help needed Urgently.
Quote:
|
Re: Problem in Flashing N900. Help needed Urgently.
Quote:
|
All times are GMT. The time now is 11:22. |
vBulletin® Version 3.8.8