I did the echo, on original 2008OS, not in R&Dmode.

Connected USB hard drive, and it automounted 27GB EXT3 partition

Awesome

[16120.085937] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[16120.085937] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[16120.210937] usb 1-1: new high speed USB device using musb_hdrc and address 12
[16120.343750] usb 1-1: default language 0x0409
[16120.343750] usb 1-1: new device strings: Mfr=56, Product=78, SerialNumber=100
[16120.343750] usb 1-1: Product: USB2.0 Storage Device
[16120.343750] usb 1-1: Manufacturer: Cypress Semiconductor
[16120.343750] usb 1-1: SerialNumber: DEF10BEEF1C7
[16120.343750] usb 1-1: device v04b4 p6830 is not supported
[16120.343750] usb 1-1: uevent
[16120.343750] usb 1-1: usb_probe_device
[16120.343750] usb 1-1: configuration #1 chosen from 1 choice
[16120.343750] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[16120.343750] usb 1-1:1.0: uevent
[16120.343750] usb-storage 1-1:1.0: usb_probe_interface
[16120.343750] usb-storage 1-1:1.0: usb_probe_interface - got id
[16120.421875] scsi0 : SCSI emulation for USB Mass Storage devices
[16120.429687] drivers/usb/core/inode.c: creating file '012'
[16120.429687] hub 1-0:1.0: 200mA power budget left
[16120.429687] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[16120.429687] hub 1-0:1.0: port 1 enable change, status 00000503
[16120.453125] usb-storage: device found at 12
[16120.453125] usb-storage: waiting for device to settle before scanning
[16125.453125] scsi 0:0:0:0: Direct-Access TOSHIBA MK3021GAS 0000 PQ
: 0 ANSI: 0
[16125.460937] SCSI device sda: 58605120 512-byte hdwr sectors (30006 MB)
[16125.476562] sda: Write Protect is off
[16125.476562] sda: Mode Sense: 27 00 00 00
[16125.476562] sda: assuming drive cache: write through
[16125.484375] SCSI device sda: 58605120 512-byte hdwr sectors (30006 MB)
[16125.484375] sda: Write Protect is off
[16125.484375] sda: Mode Sense: 27 00 00 00
[16125.484375] sda: assuming drive cache: write through
[16125.484375] sda: sda1 sda2 < sda5 >
[16125.968750] sd 0:0:0:0: Attached scsi disk sda
[16126.007812] usb-storage: device scan complete

_______________________________________





My lite-dvd burner is detected perfectly, but no driver support is present for CD

[16481.390625] musb_stage0_irq 646: CONNECT (a_host) devctl 5d
[16481.390625] hub 1-0:1.0: state 8 ports 1 chg 0000 evt 0000
[16481.390625] usb usb1: usb auto-resume
[16481.390625] usb usb1: finish resume
[16481.390625] hub 1-0:1.0: hub_resume
[16481.414062] hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[16481.570312] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x
101
[16481.695312] usb 1-1: new high speed USB device using musb_hdrc and address 15
[16481.859375] usb 1-1: default language 0x0409
[16482.031250] usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
[16482.031250] usb 1-1: Product: ATAPI-6 Bridge Controller
[16482.031250] usb 1-1: Manufacturer: Prolific Technology Inc.
[16482.031250] usb 1-1: SerialNumber: 300000000D05
[16482.031250] usb 1-1: device v2116 p0320 is not supported
[16482.031250] usb 1-1: uevent
[16482.031250] usb 1-1: usb_probe_device
[16482.031250] usb 1-1: configuration #1 chosen from 1 choice
[16482.031250] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[16482.031250] usb 1-1:1.0: uevent
[16482.031250] usb-storage 1-1:1.0: usb_probe_interface
[16482.031250] usb-storage 1-1:1.0: usb_probe_interface - got id
[16482.031250] scsi3 : SCSI emulation for USB Mass Storage devices
[16482.039062] drivers/usb/core/inode.c: creating file '015'
[16482.039062] hub 1-0:1.0: 198mA power budget left
[16482.039062] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[16482.039062] hub 1-0:1.0: port 1 enable change, status 00000503
[16482.039062] usb-storage: device found at 15
[16482.039062] usb-storage: waiting for device to settle before scanning
[16487.125000] scsi 3:0:0:0: CD-ROM LITE-ON DVDRW LDW-851S GS0P PQ : 0 ANSI: 0
[16487.164062] usb-storage: device scan complete