Thread: N900 micro sd problem
View Single Post
Henrq is offline Henrq
2013-02-23 , 12:36
Posts: 33 | Thanked: 11 times | Joined on Feb 2013
#1
I have 3 microsd cards:
1 micro sd 2gb
1 micro sdhc 8gb(it worked until yesterday)
1micro sdhc 32gb(new,it arrived yesterday)
The problem started yesterday,my n900 only mounts the micro sd 2gb,
i dont know the cause of this problem but idont think it is the magnetic cover
because the n900 reconise the 3 cards but only mounts one.
Here is the output of dmesg and lshal -m
When i remove 7gb,put the 2gb ,remove 2gb and put 32gb
Lshal -m :
Code:
home/user # lshal -m

Start monitoring devicelist:
-------------------------------------------------
08:46:09.345: platform_slide property button.state.value = true
08:46:09.359: platform_slide condition ButtonPressed = cover
08:46:17.019: platform_mmci_omap_hs_0_mmc_host property button.state.value = false
08:46:17.045: platform_mmci_omap_hs_0_mmc_host condition ButtonPressed = cover
08:46:17.549: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916 removed
08:46:17.578: volume_part1_size_7944011776 removed
08:46:17.844: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916_storage_mmc_sd_mmc removed
08:46:37.225: bme property battery.voltage.current = 3955 (0xf73)
08:46:37.244: bme property battery.reporting.current = 956 (0x3bc)
08:46:37.333: bme property battery.charge_level.percentage = 76 (0x4c)
08:46:37.492: bme property battery.remaining_time = 14400 (0x3840)
08:46:43.249: platform_mmci_omap_hs_0_mmc_host property button.state.value = true
08:46:43.261: platform_mmci_omap_hs_0_mmc_host condition ButtonPressed = cover
08:46:43.765: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916 added
08:46:44.323: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916_storage_mmc_sd_mmc added
08:46:44.662: volume_uuid_0000_6E39 added
08:46:45.037: volume_uuid_0000_6E39 property volume.mount_point = '/media/mmc1'
08:46:45.110: volume_uuid_0000_6E39 property volume.is_mounted = true
08:47:30.053: platform_mmci_omap_hs_0_mmc_host property button.state.value = false
08:47:30.085: platform_mmci_omap_hs_0_mmc_host condition ButtonPressed = cover
08:47:30.430: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916 removed
08:47:30.587: volume_uuid_0000_6E39 removed
08:47:31.035: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca58916_storage_mmc_sd_mmc removed
08:47:37.233: bme property battery.voltage.current = 3938 (0xf62)
08:47:37.242: bme property battery.reporting.current = 952 (0x3b8)
08:48:17.749: platform_mmci_omap_hs_0_mmc_host property button.state.value = true
08:48:17.789: platform_mmci_omap_hs_0_mmc_host condition ButtonPressed = cover
08:48:18.641: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca45928 added
08:48:18.852: platform_mmci_omap_hs_0_mmc_host_mmc_card_rca45928_storage_mmc_sd_mmc added
08:48:19.384: volume_part1_size_31808552960 added
08:48:37.203: bme property battery.voltage.current = 3955 (0xf73)
08:48:37.219: bme property battery.reporting.current = 948 (0x3b4)
08:49:30.672: platform_slide property button.state.value = false
08:49:30.682: platform_slide condition ButtonPressed = cover
08:49:37.201: bme property battery.voltage.current = 3961 (0xf79)
08:49:37.216: bme property battery.reporting.current = 945 (0x3b1)
dmesg:
Code:
 60.076782] SCSI subsystem initialized
[   60.621246] Driver 'sd' needs updating - please use bus_type methods
[  118.985107] mmc0: cover is open, card is now inaccessible
[  119.293334] mmc0: card e624 removed
[  139.430450] mmc0: cover is closed, card is now accessible
[  139.926910] mmc0: host does not support reading read-only switch. assuming write-enable.
[  139.926971] mmc0: new high speed SDHC card at address e624
[  139.932189] mmcblk1: mmc0:e624 SU08G 7.40 GiB 
[  139.932525]  mmcblk1: p1
[  142.760772] mmc0: cover is open, card is now inaccessible
[  142.951660] mmc0: card e624 removed
[  143.941223] mmc0: cover is closed, card is now accessible
[  144.434722] mmc0: host does not support reading read-only switch. assuming write-enable.
[  144.434783] mmc0: new high speed SDHC card at address e624
[  144.439971] mmcblk1: mmc0:e624 SU08G 7.40 GiB 
[  144.440277]  mmcblk1:<6>mmc0: cover is open, card is now inaccessible
[  144.466400]  p1
[  144.610809] Buffer I/O error on device mmcblk1, logical block 0
[  144.610900] Buffer I/O error on device mmcblk1, logical block 1
[  144.610931] Buffer I/O error on device mmcblk1, logical block 2
[  144.610961] Buffer I/O error on device mmcblk1, logical block 3
[  144.611114] Buffer I/O error on device mmcblk1, logical block 0
[  144.637786] mmc0: card e624 removed
[  147.229339] mmc0: cover is closed, card is now accessible
[  147.723785] mmc0: host does not support reading read-only switch. assuming write-enable.
[  147.723846] mmc0: new high speed SDHC card at address e624
[  147.729034] mmcblk1: mmc0:e624 SU08G 7.40 GiB 
[  147.729370]  mmcblk1: p1
[  221.726806] NET: Registered protocol family 10
[  221.727661] lo: Disabled Privacy Extensions
[  250.677124] wl12xx spi4.0: firmware: requesting wl1251-fw.bin
[  251.575408] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[  251.591003] wl1251: firmware booted (Rev 4.0.4.3.7)
[  251.747802] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  253.067779] wl1251: down
[  255.309783] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[  255.326171] wl1251: firmware booted (Rev 4.0.4.3.7)
[  255.474334] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  256.544372] wl1251: down
[  261.104034] gprs0: attached
[  462.130218] slide (GPIO 71) is now open
[ 1066.840972] slide (GPIO 71) is now closed
[ 1069.036224] kb_lock (GPIO 113) is now closed
[ 1069.434753] kb_lock (GPIO 113) is now open
[ 2095.368499] gprs0: detached
[31338.428741] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[31338.429504] regulator_disable: not in use by this consumer
[31338.429534] regulator_disable: not in use by this consumer
[31622.142028] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[31636.939025] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[31636.939605] regulator_disable: not in use by this consumer
[31636.939666] regulator_disable: not in use by this consumer
[31642.434692] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[31664.861419] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[31664.861999] regulator_disable: not in use by this consumer
[31664.862060] regulator_disable: not in use by this consumer
[31800.054260] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[31912.316192] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[31912.317047] regulator_disable: not in use by this consumer
[31912.317108] regulator_disable: not in use by this consumer
[31914.201477] slide (GPIO 71) is now open
[32095.098815] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[32095.114440] wl1251: firmware booted (Rev 4.0.4.3.7)
[32095.217620] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[32096.270904] wl1251: down
[32097.176940] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[32097.192687] wl1251: firmware booted (Rev 4.0.4.3.7)
[32097.294738] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[32098.513122] wl1251: down
[32100.057922] gprs0: attached
[34415.223724] slide (GPIO 71) is now closed
[34423.014923] mmc0: cover is open, card is now inaccessible
[34423.324615] mmc0: card e624 removed
[34449.225006] mmc0: cover is closed, card is now accessible
[34449.700347] mmc0: host does not support reading read-only switch. assuming write-enable.
[34449.700408] mmc0: new high speed SD card at address e624
[34449.706237] mmcblk1: mmc0:e624 SU02G 1.84 GiB 
[34449.706573]  mmcblk1: p1
[34496.080352] mmc0: cover is open, card is now inaccessible
[34496.387268] mmc0: card e624 removed
[34543.777801] mmc0: cover is closed, card is now accessible
[34544.583770] mmc0: host does not support reading read-only switch. assuming write-enable.
[34544.583831] mmc0: new high speed SDHC card at address b368
[34544.589385] mmcblk1: mmc0:b368 NCard 29.6 GiB 
[34544.589721]  mmcblk1: p1
[34616.528839] slide (GPIO 71) is now open
~ $
any ideas?