Win_OCF_34-2_EMMC_RM680-OEM1-916 Installed version 7.1.101, file version 7.1.41 Please make sure your device is properly powered OFF prior to connecting the USB cable. You can power your device off by holding down the power button for 8+ seconds. Flashing your device will erase all data and reset the device back to factory state. Please make sure you have backups of your data before proceeding with flashing. If flashing does not start disconnect the USB cable from the device, make sure the device is OFF and then reconnect the device with the USB cable. For first flashing you may need to repeat this a few times. Depending on amount of data to be securely erased, the erasing may take as long as 30 minutes until the flashing starts. Please, be patient. Check first that device is powered OFF and then connect USB cable. flasher 3.12.0 (Jun 30 2011) Harmattan Suitable USB interface (bootloader/phonet) not found, waiting... Found device RM-680, hardware revision 0521 NOLO version 2.0.21 Version of 'sw-release': DFL61_HARMATTAN_0.2011.11-5_RD_001 Success Status: 0 flasher 3.12.0 (Jun 30 2011) Harmattan Picked ape-algo from a FIASCO file Found device RM-680, hardware revision 0521 NOLO version 2.0.21 Version of 'sw-release': DFL61_HARMATTAN_0.2011.11-5_RD_001 Sending ape-algo image (7020 kB)... 100% (7020 of 7020 kB, avg. 26490 kB/s) Suitable USB interface (phonet) not found, waiting... Ping attempt 1 (250 ms) Server application: 1.5.26 Found product RM-680 rev. 0521 Server implements softupd protocol version 1.8 ERROR: SU_GET_PARAMETER_REQ terminated with error code 7: Object not found ERROR: Unable to get SU_PARAM_BATTERY_LEVEL ERROR: Failed to erase MMC using 'secure' method Status: 4 Press Enter to exit & Unplug the USB cable from the device to boot new flashed i mage ... Win_OCF_39-5_RM680-RM680-OEM1 IMPORTANT: READ THIS CAREFULLY AS BY DOWNLOADING, INSTALLING AND/OR USING THE NOKIA N950 ONECLICKFLASHERTнIMAGE YOU ACKNOWLEDGE AND AGREE TO THE FOLLOWING TERMS AND CONDITIONS: 1) The NOKIA N950 ONECLICKFLASHERTнIMAGE comprises of a) some software copyrighted by Nokia Corporation or third parties in binary form (collectively Licensed Software) and/or b) Open Source Software. 2) Licensed Software is distributed to you only in binary form. You a) are authorized to use the Licensed Software only in or in connection with the Nokia N950-products; and b) may not use, modify, adapt, translate, copy and/or distribute Licensed Software, except as expressly permitted herein. 3) The NOKIA N950 ONECLICKFLASHERTнIMAGE is provided to you AS IS and Nokia, its affiliates and/or its licensors do not make any representations or warranties, express or implied (including, without any limitation, the warranties of merchantability or fitness for a particular purpose, or that it will not infringe any third party patents, copyrights, trademarks or other rights). You agree that any downloading, installation and/or use by you of the NOKIA N950 ONECLICKFLASHERTнIMAGE happens and is solely at your own risk and that Nokia assumes no liability whatsoever for any damages that you may incur or suffer in connection with the NOKIA N950 ONECLICKFLASHERTнIMAGE and/or the installation or use thereof. 4) The Open Source Software is licensed and distributed under the applicable open source/free software licenses and/or other licenses, permissions, notices or disclaimers containing obligation or permission to provide the source code of such software. The relevant source code of the Open Source Software is made available to you per the product loan agreement you have concluded with us for the Nokia 950. Press Y <Ret> if your accept terms, any other key to decline y Installed version 7.1.101, file version 7.1.41 Please make sure your device is properly powered OFF prior to connecting the USB cable. You can power your device off by holding down the power button for 8+ seconds. Flashing your device will erase all data and reset the device back to factory state. Please make sure you have backups of your data before proceeding with flashing. If flashing does not start disconnect the USB cable from the device, make sure the device is OFF and then reconnect the device with the USB cable. For first flashing you may need to repeat this a few times. Depending on amount of data to be securely erased, the erasing may take as long as 30 minutes until the flashing starts. Please, be patient. Check first that device is powered OFF and then connect USB cable. First erasing eMMC Then flashing image and eMMC Flashing started at 28.07.2013 1:32:10,58 flasher 3.12.1 (Oct 6 2011) Harmattan WARNING: This tool is intended for professional use only. Using it may result in permanently damaging your device or losing the warranty. Suitable USB interface (bootloader/phonet) not found, waiting... Found device RM-680, hardware revision 0521 NOLO version 2.0.21 Version of 'sw-release': DFL61_HARMATTAN_0.2011.11-5_RD_001 Sending ape-algo image (7032 kB)... 100% (7032 of 7032 kB, avg. 27048 kB/s) Suitable USB interface (phonet) not found, waiting... Ping attempt 1 (250 ms) Server application: 1.6.3 Found product RM-680 rev. 0521 Server implements softupd protocol version 1.8 ERROR: SU_GET_PARAMETER_REQ terminated with error code 7: Object not found ERROR: Unable to get SU_PARAM_BATTERY_LEVEL ERROR: Failed to erase MMC using 'secure' method Status: 4 Flashing ended at 28.07.2013 1:32:20,32 Flashing unsuccessful Press Enter to exit
Win_OCF_22-6_EMMC_RM680-OEM1-916 Installed version 7.1.101, file version 7.1.41 Please make sure your device is properly powered OFF prior to connecting the USB cable. You can power your device off by holding down the power button for 8+ seconds. Flashing your device will erase all data and reset the device back to factory state. Please make sure you have backups of your data before proceeding with flashing. If flashing does not start disconnect the USB cable from the device, make sure the device is OFF and then reconnect the device with the USB cable. For first flashing you may need to repeat this a few times. Connect USB cable and power on the device flasher 3.11.5 (May 17 2011) Harmattan Ping attempt 1 (250 ms) Server application: 1.5.21 Found product RM-680 rev. 0521 Server implements softupd protocol version 1.8 Success Status: 0 flasher 3.11.5 (May 17 2011) Harmattan Picked ape-algo from a FIASCO file Ping attempt 1 (250 ms) Server application: 1.5.21 Found product RM-680 rev. 0521 Server implements softupd protocol version 1.8 Battery level 100 %, continuing. Erasing, this may take a while. Erase done. Success Status: 0 flasher 3.11.5 (May 17 2011) Harmattan Ping attempt 1 (250 ms) Server application: 1.5.21 Found product RM-680 rev. 0521 Server implements softupd protocol version 1.8 Image SW version DFL61_HARMATTAN_1.2011.22-6_PR_RM680 Image cert-sw not present for this HW (RM-680 rev. 0521) Image xloader not present for this HW (RM-680 rev. 0521) Image secondary not present for this HW (RM-680 rev. 0521) Image moslo not present Image tar skipped Image config skipped Battery level 99 %, continuing. image [state progress transfer flash speed] --------------------------------------------------------------------- [x] cmt-2nd [finished 100 % 95 / 95 kB NA ] [x] cmt-algo [finished 100 % 789 / 789 kB NA ] [x] cmt-mcusw [finished 100 % 6008 / 6008 kB 3021 kB/s] [x] kernel [finished 100 % 2708 / 2708 kB 1774 kB/s] [x] rootfs [finished 100 % 369567 / 369567 kB 6056 kB/s] [x] mmc [finished 100 % 152603 / 152603 kB 11622 kB/s] Updating SW release Success Status: 0 Press Enter to exit & Unplug the USB cable from the device to boot new flashed i mage ...