I need Your help! KernelPower 2.6.28.10power46 and later h-e-n were successfully installed. Nokia CA101 cable and female-to-female USB adapter used to connect flash drive. But on running h-e-n it seems that hostmode is enabled, flash device attached but not mounted because of the errors which I do not understand. I don't know, maybe I had to do something manually exept the aboveinstallation procedures? Here I give ending part of the dump of Kernel Messages (because the full one is too long). Suppose You shall know the answer after taking a look on it. The full text You can find in the attached file.

................
[ 1919.932128] usb 1-1: device not accepting address 43, error -71
[ 1920.057159] usb 1-1: new high speed USB device using musb_hdrc and address 44
[ 1920.479095] usb 1-1: device not accepting address 44, error -71
[ 1920.479217] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1920.479278] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 1920.479339] hub 1-0:1.0: port 1 enable change, status 00000501
[ 1923.197845] hub 1-0:1.0: hub_suspend
[ 1923.197937] usb usb1: bus auto-suspend
[ 1934.969451] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[ 1954.068634] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[ 1955.553680] usb usb1: usb resume
[ 1955.573089] hub 1-0:1.0: hub_resume
[ 1955.573211] hub 1-0:1.0: port 1: status 0101 change 0001
[ 1955.682189] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 1955.682281] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 1955.807281] usb 1-1: new high speed USB device using musb_hdrc and address 45
[ 1955.956329] usb 1-1: default language 0x0409
[ 1955.957641] usb 1-1: uevent
[ 1955.957824] usb 1-1: usb_probe_device
[ 1955.957855] usb 1-1: configuration #1 chosen from 1 choice
[ 1955.961608] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 1955.961944] usb 1-1:1.0: uevent
[ 1955.962188] libusual 1-1:1.0: usb_probe_interface
[ 1955.962280] libusual 1-1:1.0: usb_probe_interface - got id
[ 1955.962432] usb-storage 1-1:1.0: usb_probe_interface
[ 1955.962524] usb-storage 1-1:1.0: usb_probe_interface - got id
[ 1956.059661] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1956.065734] /home/builder2/maemo-fremantle-armel-extras-devel/work/kernel-power-2.6.28/drivers/usb/core/inode.c: creating file '045'
[ 1956.066436] usb 1-1: New USB device found, idVendor=0781, idProduct=5406
[ 1956.066467] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1956.066497] usb 1-1: Product: U3 Cruzer Micro
[ 1956.066528] usb 1-1: Manufacturer: SanDisk Corporation
[ 1956.066558] usb 1-1: SerialNumber: 000017F9AC652EB4
[ 1956.066619] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 1956.066711] hub 1-0:1.0: port 1 enable change, status 00000503
[ 1956.090637] usb-storage: device found at 45
[ 1956.090667] usb-storage: waiting for device to settle before scanning
[ 1961.090209] usb-storage: device scan complete
[ 1961.091674] scsi 6:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2
[ 1961.092407] scsi 6:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2
[ 1961.113677] sd 6:0:0:0: [sda] 8015502 512-byte hardware sectors: (4.10 GB/3.82 GiB)
[ 1961.114196] sd 6:0:0:0: [sda] Write Protect is off
[ 1961.114227] sd 6:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 1961.114257] sd 6:0:0:0: [sda] Assuming drive cache: write through
[ 1961.122314] sd 6:0:0:0: [sda] 8015502 512-byte hardware sectors: (4.10 GB/3.82 GiB)
[ 1961.122802] sd 6:0:0:0: [sda] Write Protect is off
[ 1961.122833] sd 6:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 1961.122863] sd 6:0:0:0: [sda] Assuming drive cache: write through
[ 1961.122924] sda: sda1
[ 1961.143615] sd 6:0:0:0: [sda] Attached SCSI removable disk