Dear Guys,,

Its still not working. Really need your assistance since this the only type that been sell. Really need to get this adapter work.

FYI. i had copy the usbnet.ko to /lib/modules/2.6.28.10power46 and copy the file sr9600.ko to /home/opt/usb2net/module and opt/usb2net/module and after i run insmode sr9600;ko at both location i get same error "inserting sr9600.ko:-1 unknown symbol in module" and under dmesg it just show 1 error [81459.421966] sr9600: Unknown symbol __bad_udelay"

Try to run h-e-n still not working getting below messages.

[117868.085937] sr9600: Unknown symbol __bad_udelay
[117900.744262] slide (GPIO 71) is now closed
[117916.822479] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[117943.400512] slide (GPIO 71) is now open
[117966.525451] slide (GPIO 71) is now closed
[117977.695343] usb usb1: usb resume
[117977.712890] hub 1-0:1.0: hub_resume
[117977.713012] hub 1-0:1.0: port 1: status 0101 change 0001
[117977.822540] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[117977.822631] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[117977.947418] usb 1-1: new full speed USB device using musb_hdrc and address 99
[117978.095764] usb 1-1: ep0 maxpacket = 8
[117978.096832] usb 1-1: default language 0x0409
[117978.098602] usb 1-1: uevent
[117978.098815] usb 1-1: usb_probe_device
[117978.098846] usb 1-1: configuration #1 chosen from 1 choice
[117978.102233] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[117978.102569] usb 1-1:1.0: uevent
[117978.105194] /home/builder2/maemo-fremantle-armel-extras-devel/work/kernel-power-2.6.28/drivers/usb/core/inode.c: creating file '099'
[117978.105895] usb 1-1: New USB device found, idVendor=0fe6, idProduct=8101
[117978.105957] usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=3
[117978.105987] usb 1-1: Product: USB Network Controller
[117978.106018] usb 1-1: SerialNumber:
[117978.106048] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[117978.106140] hub 1-0:1.0: port 1 enable change, status 00000103
[117994.048889] slide (GPIO 71) is now open
/home/user # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:10360 errors:0 dropped:0 overruns:0 frame:0
TX packets:10360 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:616991 (602.5 KiB) TX bytes:616991 (602.5 KiB)

phonet0 Link encap:UNSPEC HWaddr 15-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP POINTOPOINT RUNNING NOARP MTU:4000 Metric:1
RX packets:38208 errors:0 dropped:0 overruns:0 frame:0
TX packets:7490 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:17187936 (16.3 MiB) TX bytes:367854 (359.2 KiB)

/home/user # usbEthUp.sh
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/rtl8150.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/mcs7830.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/dm9601.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/smsc95xx.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/kaweth.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/pegasus.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/plusb.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/gl620a.ko': -1 File exists
insmod: error inserting '/lib/modules/2.6.28.10power46/usb2net/catc.ko': -1 File exists
udhcpc (v0.9.9-pre) started
SIOCGIFINDEX failed!: No such device
/home/user # lsusb
Bus 001 Device 099: ID 0fe6:8101
Bus 001 Device 001: ID 1d6b:0002
/home/user # udhcpc
udhcpc (v0.9.9-pre) started
SIOCGIFINDEX failed!: No such device
/home/user # ifconfig eth0 up
ifconfig: SIOCGIFFLAGS: No such device
/home/user # ls /dev/eth*
ls: /dev/eth*: No such file or directory
/home/user #