I'm back again,

Tried over the weekend the above, without it working. Used flasher to set to R&D mode and turn USB Host on, still no luck. Ran dmesg and got this
4.024444] tahvo: Registering interrupt 1 for device
[ 4.505310] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OMAP)
[ 4.527130] ohci ohci: OMAP OHCI
[ 4.549194] ohci ohci: new USB bus registered, assigned bus number 1
[ 4.549377] ohci ohci: irq 38, io mem 0xfffba000
[ 4.644042] usb usb1: configuration #1 chosen from 1 choice
[ 4.666107] hub 1-0:1.0: USB hub found
[ 4.666351] hub 1-0:1.0: 3 ports detected
[ 4.898895] usbcore: registered new driver usbhid
[ 4.899047] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 5.090972] usbcore: registered new driver usbserial
[ 5.091125] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 5.312103] SCSI subsystem initialized
[ 5.504394] Initializing USB Mass Storage driver...
[ 5.526336] usbcore: registered new driver usb-storage
[ 5.526489] USB Mass Storage support registered.
[ 5.618835] drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
[ 5.640686] usbcore: registered new driver pl2303
[ 5.640838] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
[ 5.721740] usbcore: registered new driver net1080
[ 5.794342] usbcore: registered new driver cdc_ether
[ 5.896179] usbcore: registered new driver asix
[ 6.394866] Selected HOST mode: host controller present.
[ 6.395202] ohci ohci: wakeup
[ 6.395324] USB cable disconnected
[ 6.852081] usb 1-1: new low speed USB device using ohci and address 2
[ 7.458343] usb 1-1: device descriptor read/64, error -110
[ 7.762664] usb 1-1: device descriptor read/64, error -110
[ 7.853576] umac: module license 'Proprietary' taints kernel.
[ 8.067443] usb 1-1: new low speed USB device using ohci and address 3
[ 8.074920] CX3110x chip variant: STLC4370
[ 8.196380] CX3110x: firmware version: 2.13.0.0.a.13.14
[ 8.196594] Loaded CX3110x driver, version 0.8
[ 8.262725] usb 1-1: device descriptor read/64, error -110
[ 8.567260] usb 1-1: device descriptor read/64, error -110
[ 8.875061] usb 1-1: new low speed USB device using ohci and address 4
[ 9.293914] usb 1-1: device not accepting address 4, error -110
[ 9.489227] usb 1-1: new low speed USB device using ohci and address 5
[ 9.918945] usb 1-1: device not accepting address 5, error -110
[ 24.036315] omapdsp: mapping in ARM MMU, v=0xe0fff000, p=0x13c00000, sz=0x1000

I'm searching for what is an "error -100" but have not found it yet.

Does re-flashing the 700 replace everything? or are there some info retained by the 770?

Thanks Again
Faithful

Seems like the USB device isent supported. What is it?

Yep, all is gone. (except for whatever is on the memory card.)

mrlanrat

I re flashed my unit, but it still remembered what date it was. Is there a factory reset on this unit?

faithful

It may be similar to a PC clock in BIOS: It keeps the time even if you disconnect it from the wall... I don't think there is user accessible CMOS reset button/jumper in any of the Tablets.

Dear Mara,

Thanks.
I still trying to get the usb port working (error 100), any Hints?

Faithful

I dident re-flash mine when I did it. I just made the script and ran it, that was all.

If you have a usb keyboard try using that. it dosent require any drivers and should work automatically, and it will let us know if the usb is even working at all. maby your usb power inverted is bad?

mrlant,
Tried the usb keyboard, I can type, but hitting the enter key brings up the on screen keyboard. I saw something about that before, I'll have to find it again.

Flash drive is now listed as a scsi device, but I have not been able to figure out how or where to mount. Will try again latter

[ 3432.894927] usb 1-1: new full speed USB device using ohci and address 40
[ 3433.134796] usb 1-1: device v13fe p1d00 is not supported
[ 3433.136779] usb 1-1: configuration #1 chosen from 1 choice
[ 3433.166534] scsi0 : SCSI emulation for USB Mass Storage devices
[ 3433.183410] usb-storage: device found at 40
[ 3433.183471] usb-storage: waiting for device to settle before scanning
[ 3438.186950] Vendor: Kingston Model: DataTraveler 2.0 Rev: PMAP
[ 3438.187164] Type: Direct-Access ANSI SCSI revision: 00
[ 3439.115081] SCSI device sda: 4030464 512-byte hdwr sectors (2064 MB)
[ 3439.120788] sda: Write Protect is off
[ 3439.120849] sda: Mode Sense: 23 00 00 00
[ 3439.120910] sda: assuming drive cache: write through
[ 3439.144866] SCSI device sda: 4030464 512-byte hdwr sectors (2064 MB)
[ 3439.150787] sda: Write Protect is off
[ 3439.150848] sda: Mode Sense: 23 00 00 00
[ 3439.150878] sda: assuming drive cache: write through
[ 3439.150970] sda: sda1

Thanks for your help

faithful

Gave it another shot this morning, and it is working!?
Only thing is I not sure what fixed it. But what I did
a: set to r&D mode
b: with flasher, set to host mode.
c: checked batteries in power inverter
d: checked all connections.

This did not work yesterday, but plugged it in this morning and it worked. I'm a happy camper.
faithful