Notices
Page 59 of 90 « First 495758 59 606169 Last »
Reply
Thread Tools
rayon is offline rayon
2012-05-01 , 10:51
Posts: 6 | Thanked: 0 times | Joined on May 2012
#581
Originally Posted by g0r View Post
If you recently upgraded your kp to 50 latest then you have to upgrade the injection drivers to be compatible with the new kernel power. Get the new injection drivers in the same place here
Also you can read few posts back about cleven and compatibility with kp50.
Hello,

I copied the drivers provided from http://david.gnedt.eu/blog/wl1251/ to /opt/cleven/compat-wireless-v1. I could load them but I can't set it to monitor mode through cleven interface (I can do it manually). But still, I can't scan for network.

So I read few post back and I found the following solution :
http://talk.maemo.org/showpost.php?p...&postcount=541

I tried it but it doesn't work I have the same symptom (can't set the driver to monitor mode through the interface and I can't scan for network).

Regards,
 
Saturn's Avatar
Saturn is offline Saturn
2012-05-01 , 10:54
Posts: 1,648 | Thanked: 2,122 times | Joined on Mar 2007 @ UNKLE's Never Never Land
#582
Originally Posted by rayon View Post
Hello,

I have two issues after installing cleven 2.5.2 :
- I can't scan for network after setting monitor mode and loading injection driver ;
- I have not the reaver/wps button on the interface whereas I have reaver and walsh installed.

1) When I click on "scan" button I have the following error :
PHP Code:
ERROR: Cannot scan for available networks.
 
The drivers or the interface are not to the correct state.
Please configure them from the available menu option. 
By looking loaded modules I can't see wl1251. I see wl12xx instead. So I launched load.sh script from /opt/cleven (with -v2 switch) and I can see the right driver from cleven loaded. But, I can't set this driver to monitor mode, iwconfig command show me managed mode on wifi interface (wlan0).

2) I installed reaver and walsh and I can use them but cleven interface didn't show the reaver or wps button.

PHP Code:
$ uname -a
Linux Nokia-N900 2.6.28.10-power50 #1 PREEMPT Sun Mar 18 20:10:56 EET 2012 armv7l GNU/Linux

$ dpkg -l |grep cleven
ii  cleven     2.5-2        Cleven is a user interface of aircrack-ng and reaver for the N900. 
Regards,

Can you run the app from the xterm (as user) and post if you see anything strange?

How did you install reaver?
__________________
Packages: elGR Locale, SMSCON Editor, Swappolube, CSSU Features Configuration, Snuggle, YAMAS, Cleven
 Garage: SMSCON, Swappolube, CSSU Features Configuration, Snuggle
Wiki: SMSCON, SMSCON Editor, Swappolube, CSSU Features Configuration, Cleven
 

The Following User Says Thank You to Saturn For This Useful Post:
Saturn's Avatar
Saturn is offline Saturn
2012-05-01 , 10:56
Posts: 1,648 | Thanked: 2,122 times | Joined on Mar 2007 @ UNKLE's Never Never Land
#583
Originally Posted by rayon View Post
Hello,

I copied the drivers provided from http://david.gnedt.eu/blog/wl1251/ to /opt/cleven/compat-wireless-v1. I could load them but I can't set it to monitor mode through cleven interface (I can do it manually). But still, I can't scan for network.

So I read few post back and I found the following solution :
http://talk.maemo.org/showpost.php?p...&postcount=541

I tried it but it doesn't work I have the same symptom (can't set the driver to monitor mode through the interface and I can't scan for network).

Regards,
If you have done any of the above it is best you uninstall cleven and then re-install.

None of those are needed for the devel version you are using.
__________________
Packages: elGR Locale, SMSCON Editor, Swappolube, CSSU Features Configuration, Snuggle, YAMAS, Cleven
 Garage: SMSCON, Swappolube, CSSU Features Configuration, Snuggle
Wiki: SMSCON, SMSCON Editor, Swappolube, CSSU Features Configuration, Cleven
 
g0r is offline g0r
2012-05-01 , 11:02
Posts: 105 | Thanked: 87 times | Joined on Jun 2011 @ Unknown
#584
Originally Posted by rayon View Post
Hello,

I copied the drivers provided from http://david.gnedt.eu/blog/wl1251/ to /opt/cleven/compat-wireless-v1. I could load them but I can't set it to monitor mode through cleven interface (I can do it manually). But still, I can't scan for network.

So I read few post back and I found the following solution :
http://talk.maemo.org/showpost.php?p...&postcount=541

I tried it but it doesn't work I have the same symptom (can't set the driver to monitor mode through the interface and I can't scan for network).

Regards,
follow david's instruction (read me file) on his page still old but pretty same for new injection driver, worked for me and other people.
 
g0r is offline g0r
2012-05-01 , 11:15
Posts: 105 | Thanked: 87 times | Joined on Jun 2011 @ Unknown
#585
Originally Posted by Saturn View Post
If you have done any of the above it is best you uninstall cleven and then re-install.

None of those are needed for the devel version you are using.
Saturn please correct me if I am wrong but that will not work as he is on kp50 with old injection drivers installed in wl1251-maemo folder so if he was using kp49 then yes with the latest version of cleven that will work but what he did was just copied the new injection drivers to opt/cleven so he is on kp50 with old injection drviers installed in wl1251-maemo and new injection drivers in opt/cleven how will that work?
 
rayon is offline rayon
2012-05-01 , 11:23
Posts: 6 | Thanked: 0 times | Joined on May 2012
#586
Originally Posted by Saturn View Post
If you have done any of the above it is best you uninstall cleven and then re-install.

None of those are needed for the devel version you are using.

Thank you.

I remove cleven with application manager and then I purge it using
the following command :
dpkg --purge cleven

Then I reinstall it and all works fine.

However, the reaver/wps button doesn't appears and the interface.

I installed reaver and washl by copying the binary from http://forums.internettablettalk.com...5&postcount=60

Next, I copied reaver.db into /etc/reaver. (reaver and washl binary is under /bin/ directory).

Regards,
 
rayon is offline rayon
2012-05-01 , 11:26
Posts: 6 | Thanked: 0 times | Joined on May 2012
#587
Originally Posted by Saturn View Post
If you have done any of the above it is best you uninstall cleven and then re-install.

None of those are needed for the devel version you are using.
Thanks you it works, injection driver is loaded and I can scan for network. I remove cleven usin application manager and I purge it
using the following command : dpkg --purge cleven. Next, I reinstall it.

However, I have an issue with reaver. I install it by downloading the
binaries from: http://forums.internettablettalk.com...5&postcount=60

I copied the binary under /bin and I copied reaver.db under /etc/reaver.

Regards,
 
rayon is offline rayon
2012-05-01 , 11:44
Posts: 6 | Thanked: 0 times | Joined on May 2012
#588
I remove, purge and reinstall it and it works I can scan for networks. Now I have the last issue it concern reaver. I install it by downloading this package : http://forums.internettablettalk.com...5&postcount=60

I copied the binaries under /bin and reaver.db under /etc/reaver. When I launched reaver I have the following output :
PHP Code:
# reaver -i wlan0 -b xx:xx:xx:xx:xx:xx -vv
[...]
[-] Failed to initialize interface 'wlan0'
[-] Failed to recover WPA key
[-] Nothing done, nothing to save. 
wlan0 interface has monitor mode activated.

Regards,
 
Saturn's Avatar
Saturn is offline Saturn
2012-05-01 , 12:46
Posts: 1,648 | Thanked: 2,122 times | Joined on Mar 2007 @ UNKLE's Never Never Land
#589
Originally Posted by g0r View Post
Saturn please correct me if I am wrong but that will not work as he is on kp50 with old injection drivers installed in wl1251-maemo folder so if he was using kp49 then yes with the latest version of cleven that will work but what he did was just copied the new injection drivers to opt/cleven so he is on kp50 with old injection drviers installed in wl1251-maemo and new injection drivers in opt/cleven how will that work?
Hi,

as you will notice in the changelog (posted in this thread and here: http://maemo.org/packages/view/cleven/) the last version in devel provides support for KP50 too.

This release of Cleven has both versions of the drivers (new and old) included and the one to be used is automatically selected depending on the KP used.

hope it helps
__________________
Packages: elGR Locale, SMSCON Editor, Swappolube, CSSU Features Configuration, Snuggle, YAMAS, Cleven
 Garage: SMSCON, Swappolube, CSSU Features Configuration, Snuggle
Wiki: SMSCON, SMSCON Editor, Swappolube, CSSU Features Configuration, Cleven
 

The Following User Says Thank You to Saturn For This Useful Post:
rayon is offline rayon
2012-05-01 , 13:02
Posts: 6 | Thanked: 0 times | Joined on May 2012
#590
Originally Posted by Saturn View Post
If you have done any of the above it is best you uninstall cleven and then re-install.

None of those are needed for the devel version you are using.
Hello,

it works I remove it and purge it. Now I can scan for network. But I've an issue with reaver. I can launch it with the command line and it works fine. But through cleven capture interface I can't see reaver/wps button.

I installed reaver by downloading this package : http://forums.internettablettalk.com...5&postcount=60

And I copied binaries under /bin and reaver.db in /home/user/.reaver which is linked to /etc/reaver.

Regards,
 
Reply
Page 59 of 90 « First 495758 59 606169 Last »

Tags
aircrack, cleven, reaver

« Previous Thread | Next Thread »
Thread Tools

 
Forum Jump


All times are GMT. The time now is 17:49.

Contact Us - Home - Archive - Top