Active Topics
-
List of well performing apps on Leste (35)
to Maemo 7 / Leste by smatkovi - 2 days, 7 hrs ago -
Porting apps to Leste (43)
to Maemo 7 / Leste by teroyk - 2 days, 13 hrs ago -
Sailfish OS for the Motorola Moto G7 Power (XT1955-5) - (ocean) (13)
to SailfishOS by edp17 - 3 days, 5 hrs ago -
Sailfish OS for the Samsung Galaxy Note 4 (SM-N910C) - (treltexx) (79)
to SailfishOS by edp17 - 3 days, 5 hrs ago -
U-Boot for Nokia RX-51 with BootMenu (updated version 2012.10-rc3-1) (843)
to Alternatives by Arno_11 - 3 days, 10 hrs ago -
Maemo repository (5)
to Community by dredlok706 - 6 days, 5 hrs ago -
Re-commissioning N9 in 2018 (127)
to MeeGo / Harmattan by smatkovi - 6 days, 8 hrs ago - more...
|
2006-05-09
, 16:33
|
|
Posts: 319 |
Thanked: 6 times |
Joined on Apr 2006
|
#2
|
Originally Posted by kkwansj
Haven't seen that problem. However in answer to the second part, with the cover on, it should be in power saving mode. Hoever even in power saving mode it still draws power, just not as much. It should last about a week in standby.The other morning I shut down my 770, and sat it beside me. Later in the day, I hear Nokia startup tune come from my tablet. I slid it open and sure enought, it was on. Has anyone else had this happen?
On a related note, if it were to be powered up, while the hard cover is still on, is it really running, or does it go into some sort of power save mode?
However, I just tested and couldn't get my nokia to power up while the case was on, after I pulled it out, and turned it on, it did complete the start up with the case on, so this is just strange. See if it happens anymore or if this time was just a fluke.
|
|
2006-05-09
, 18:38
|
|
Posts: 9 |
Thanked: 1 time |
Joined on Apr 2006
|
#3
|
Originally Posted by rattis
So, with the cover on, it should never be able to power up? There were several times where I slid open the case, and found the device on. My initial impression was that the power button was pressed while sitting in my bag. But given what you said, then there is indeed something strange going on.
Haven't seen that problem. However in answer to the second part, with the cover on, it should be in power saving mode. Hoever even in power saving mode it still draws power, just not as much. It should last about a week in standby.
However, I just tested and couldn't get my nokia to power up while the case was on, after I pulled it out, and turned it on, it did complete the start up with the case on, so this is just strange. See if it happens anymore or if this time was just a fluke.
|
|
2006-05-09
, 18:47
|
|
Posts: 9 |
Thanked: 1 time |
Joined on Apr 2006
|
#4
|
Additional info: It is currently running OS version 5.2006.13-7
|
|
2006-05-09
, 21:45
|
|
Posts: 319 |
Thanked: 6 times |
Joined on Apr 2006
|
#5
|
Originally Posted by kkwansj
I'm running the the older (december) release software. However when I tell the device to switch off, and it shuts down. With the case on it does not come back on when pressing the button.Additional info: It is currently running OS version 5.2006.13-7
If you have a box that you can do it with. Connect via wifi to a network and then ping the 770, keep the ping going while you put the case back over the screen. If the ping does not fail, it means that you're 770 doesn't see the case when it's on, and it's not going into stand by (you can probably test this by looking in the 1mm gap between the case and the unit to see if the screen is lit).
|
|
2006-05-09
, 21:55
|
|
Posts: 9 |
Thanked: 1 time |
Joined on Apr 2006
|
#6
|
Originally Posted by rattis
Alright, I will monitor it the next few days and report back.I'm running the the older (december) release software. However when I tell the device to switch off, and it shuts down. With the case on it does not come back on when pressing the button.
If you have a box that you can do it with. Connect via wifi to a network and then ping the 770, keep the ping going while you put the case back over the screen. If the ping does not fail, it means that you're 770 doesn't see the case when it's on, and it's not going into stand by (you can probably test this by looking in the 1mm gap between the case and the unit to see if the screen is lit).
Thanks!
|
|
2006-05-09
, 22:19
|
|
Posts: 79 |
Thanked: 1 time |
Joined on Nov 2005
|
#7
|
Originally Posted by rattis
There are two easier ways to test this:If you have a box that you can do it with. Connect via wifi to a network and then ping the 770, keep the ping going while you put the case back over the screen. If the ping does not fail, it means that you're 770 doesn't see the case when it's on, and it's not going into stand by (you can probably test this by looking in the 1mm gap between the case and the unit to see if the screen is lit).
1. If wifi is connected, closing the lid should shut wifi off. Just slide the lid on and off; if wifi disconnected automatically then it sensed the lid.
2. Use the hardware zoom buttons, or really any other button you can reach with the lid on. Close the lid, press zoom 10 times, open the lid. If the dot on the i fills your screen, then the button was doing something and it didn't know the lid was closed.
|
|
2006-05-09
, 22:42
|
|
Posts: 182 |
Thanked: 3 times |
Joined on Mar 2006
|
#8
|
This has been happening to me on the old December software and the new March/April software. What happens is that when you press the Power button, it powers up but doesn't necessarily turn on. So when you take off the case it starts loading without having to press the power button. But in some of my other experiences, it loads even with the case on. Very buggy....
|
|
2006-05-10
, 00:17
|
|
Posts: 137 |
Thanked: 8 times |
Joined on Apr 2006
|
#9
|
strange that you mentioned that your machine turns on by its self. i have not notice my turn on but i have found that my battery was dead after knowing that i have turned it off the night before on several occassions. i know that or thought that i turned it off correctly but may be not.
|
|
2006-05-10
, 00:54
|
|
Posts: 182 |
Thanked: 3 times |
Joined on Mar 2006
|
#10
|
Actually, I just tested mine a few times. If you press the power button like you normally would to turn it on while in the case, it still powers on. You can even see the light power on when you look at it through the side. I guess this is a bug they have to fix in the next update?
On a related note, if it were to be powered up, while the hard cover is still on, is it really running, or does it go into some sort of power save mode?