Active Topics
-
Camera phone competition March 2023 "Endless" (35)
to General by Maemish - 1 day, 12 hrs ago -
TLS 1.2 for N9 is ready (28)
to MeeGo / Harmattan by smartblu9 - 1 day, 13 hrs ago -
Maemo repository (3)
to Community by torsen - 2 days, 5 hrs ago -
Error after installing Leste on sdcard (11)
to Maemo 7 / Leste by Maemish - 3 days, 3 hrs ago -
Introducing ubiboot N9 (multiboot OS loader) (1,393)
to Alternatives by smatkovi - 4 days, 9 hrs ago - more...
 |
|
2014-03-28
, 11:20
|
|
Posts: 562 |
Thanked: 2,744 times |
Joined on Dec 2013
@ Espoo, Finland
|
#672
|
toh-vdd supply is now "shutdown" when display is off,
but first keypress can send some dbus-spells to change to tohkbd-layout (minimal) - forcing landscape needs some digging
Only problem here is how to get easily back to normal vkb. maybe add quick-button to the tohkbd-layout to restore previously used vkb layout
but first keypress can send some dbus-spells to change to tohkbd-layout (minimal) - forcing landscape needs some digging
Only problem here is how to get easily back to normal vkb. maybe add quick-button to the tohkbd-layout to restore previously used vkb layout
|
|
2014-03-29
, 00:46
|
|
Posts: 5 |
Thanked: 4 times |
Joined on May 2013
@ Bulgaria, Sofia
|
#673
|
dirkvl: I'm really sorry for writing it here, but my account is limited and I can't send private messages.
I would like to purchase one from your Qwerty OtherHalfs. Do you have some already made Qwerty OtherHalfs for sell or if I purchase one now, I'll be in the waiting list? If I pay you tomorrow, when can I expect to receive my keyboard? How could I do the purchase? Do you prefer PayPal or a regular Bank transfer (I have it both PayPal and Bank account)? Bank transfer is slower, but is free of charge for you (or should be free of charge for you). I have already read that the shipping costs to my country - Bulgaria (Classified as EUR2 in the table) are 11 EUR, so the total price with the shipment should be 111 EUR for me?
Please, add me to the waiting list and tell me how to proceed with my order.
Best regards
Yasen Iliev (Ясен Илиев)
I would like to purchase one from your Qwerty OtherHalfs. Do you have some already made Qwerty OtherHalfs for sell or if I purchase one now, I'll be in the waiting list? If I pay you tomorrow, when can I expect to receive my keyboard? How could I do the purchase? Do you prefer PayPal or a regular Bank transfer (I have it both PayPal and Bank account)? Bank transfer is slower, but is free of charge for you (or should be free of charge for you). I have already read that the shipping costs to my country - Bulgaria (Classified as EUR2 in the table) are 11 EUR, so the total price with the shipment should be 111 EUR for me?
Please, add me to the waiting list and tell me how to proceed with my order.
Best regards
Yasen Iliev (Ясен Илиев)
|
|
2014-03-29
, 06:47
|
|
Posts: 10 |
Thanked: 7 times |
Joined on Mar 2014
@ Finland
|
#674
|
Originally Posted by octane
http://talk.maemo.org/showpost.php?p...&postcount=619
dirkvl: I'm really sorry for writing it here, but my account is limited and I can't send private messages.
I would like to purchase one from your Qwerty OtherHalfs. Do you have some already made Qwerty OtherHalfs for sell or if I purchase one now, I'll be in the waiting list? If I pay you tomorrow, when can I expect to receive my keyboard? How could I do the purchase? Do you prefer PayPal or a regular Bank transfer (I have it both PayPal and Bank account)? Bank transfer is slower, but is free of charge for you (or should be free of charge for you). I have already read that the shipping costs to my country - Bulgaria (Classified as EUR2 in the table) are 11 EUR, so the total price with the shipment should be 111 EUR for me?
Please, add me to the waiting list and tell me how to proceed with my order.
Best regards
Yasen Iliev (Ясен Илиев)
|
|
2014-03-30
, 01:39
|
|
Posts: 5 |
Thanked: 4 times |
Joined on May 2013
@ Bulgaria, Sofia
|
#675
|
O.K. than I'll try to make it by my own. Maybe with some modifications:
1. I'll try to add 2 additional keys (below the unlabelled keys of the Motorolas keyboard )
2. I'll try to attach a hall diode and connect it so, that its signal will be reported as a keypress. I'll check if the magnetic field of the speaker is strong enough to be detected from the hall diode. If not, I'll add a magnet too.
3. I'll install a metallic coin in the keyboard to be able to attach the phone on my custom build magnetic car phone holder. (Now the coin with some cuts on it is replacing the rubber near the Sim card)
I'm unsure about one thing. Please, someone with a keyboard to answer me: Is the QWERTY back good connected to the phone? Is there a chance that the QWERTY back could fall from the phone during the use of it? My original back haven't fall from the phone, but the QWERTY back is significant heavier as the original one. Should I provide a 4 bolt holes on the edges of my QWERTY back and connect the back wit the phone trough replacing the original 4 bolts from the phones edges with a longer bolts trough the QWERTY back, or the design from dirkvl is enough safe against falling of the back from the phone?
P.S.
And the last question: Is there a way to buy the hinge from the partlist, without buying the BT keyboard?
Last edited by octane; 2014-03-30 at 01:44.
1. I'll try to add 2 additional keys (below the unlabelled keys of the Motorolas keyboard )
2. I'll try to attach a hall diode and connect it so, that its signal will be reported as a keypress. I'll check if the magnetic field of the speaker is strong enough to be detected from the hall diode. If not, I'll add a magnet too.
3. I'll install a metallic coin in the keyboard to be able to attach the phone on my custom build magnetic car phone holder. (Now the coin with some cuts on it is replacing the rubber near the Sim card)
I'm unsure about one thing. Please, someone with a keyboard to answer me: Is the QWERTY back good connected to the phone? Is there a chance that the QWERTY back could fall from the phone during the use of it? My original back haven't fall from the phone, but the QWERTY back is significant heavier as the original one. Should I provide a 4 bolt holes on the edges of my QWERTY back and connect the back wit the phone trough replacing the original 4 bolts from the phones edges with a longer bolts trough the QWERTY back, or the design from dirkvl is enough safe against falling of the back from the phone?
P.S.
And the last question: Is there a way to buy the hinge from the partlist, without buying the BT keyboard?
Last edited by octane; 2014-03-30 at 01:44.
|
|
2014-04-01
, 16:55
|
|
Posts: 562 |
Thanked: 2,744 times |
Joined on Dec 2013
@ Espoo, Finland
|
#676
|
URGENT
You need to disable TOHKBD daemon when using TOHOLED and way around too. These will fight about the I2C bus and other controls, and for sure may cause reboots and other malfunctions described by Kabouik.
And now i wish dirkvl would have put that EEPROM there, i did make some udevrules to start and stop daemons as needed based on EEPROM content. But maybe those can be done by NFC too.
(needs that TOH-switch-dimple on toh)
You need to disable TOHKBD daemon when using TOHOLED and way around too. These will fight about the I2C bus and other controls, and for sure may cause reboots and other malfunctions described by Kabouik.
Code:
systemctl stop tohkbd.service systemctl disable tohkbd.service systemctl enable toholed.service systemctl start toholed.service
Code:
systemctl stop toholed.service systemctl disable toholed.service systemctl enable tohkbd.service systemctl start tohkbd.service
And now i wish dirkvl would have put that EEPROM there, i did make some udevrules to start and stop daemons as needed based on EEPROM content. But maybe those can be done by NFC too.
(needs that TOH-switch-dimple on toh)
|
|
2014-04-01
, 19:21
|
|
Posts: 1,104 |
Thanked: 5,652 times |
Joined on Feb 2010
@ Holland
|
#677
|
Originally Posted by octane
Sounds good!
O.K. than I'll try to make it by my own. Maybe with some modifications:
1. I'll try to add 2 additional keys (below the unlabelled keys of the Motorolas keyboard )
2. I'll try to attach a hall diode and connect it so, that its signal will be reported as a keypress. I'll check if the magnetic field of the speaker is strong enough to be detected from the hall diode. If not, I'll add a magnet too.
3. I'll install a metallic coin in the keyboard to be able to attach the phone on my custom build magnetic car phone holder. (Now the coin with some cuts on it is replacing the rubber near the Sim card)
Originally Posted by octane
By phone is pretty banged up, but the keyboard clips fine!
Is the QWERTY back good connected to the phone? Is there a chance that the QWERTY back could fall from the phone during the use of it? Should I provide a 4 bolt holes on the edges of my QWERTY back and connect the back wit the phone trough replacing the original 4 bolts from the phones edges with a longer bolts trough the QWERTY back?
Originally Posted by octane
No.
And the last question: Is there a way to buy the hinge from the partlist, without buying the BT keyboard?
| The Following User Says Thank You to dirkvl For This Useful Post: | ||
|
|
2014-04-01
, 19:37
|
|
Posts: 2,076 |
Thanked: 3,268 times |
Joined on Feb 2011
|
#678
|
Originally Posted by dirkvl
I would warn about the opposite, last time I needed 10 min battery off restart prying off hwkb oh noticed that phone part was getting loose from screen part. If it's thard to clip on STOP, get some fine sandpaper and file down the parts kimmo pictured few posts ago. you can damage your phone on remove (possible fix that worked for me, don't go speaker corner, find one which does come loose, mine was upper right, oh is off until weekend visit to granpa, he has some paper, not gonna risk it)
By phone is pretty banged up, but the keyboard clips fine!
|
|
2014-04-01
, 19:47
|
|
Posts: 1,104 |
Thanked: 5,652 times |
Joined on Feb 2010
@ Holland
|
#679
|
Originally Posted by szopin
i heard that...
I would warn about the opposite, last time I needed 10 min battery off restart prying off hwkb oh noticed that phone part was getting loose from screen part. If it's thard to clip on STOP, get some fine sandpaper and file down the parts kimmo pictured few posts ago. you can damage your phone on remove (possible fix that worked for me, don't go speaker corner, find one which does come loose, mine was upper right, oh is off until weekend visit to granpa, he has some paper, not gonna risk it)
2nd batch and updated CAD model is 0.05% larger and no longer seems to have this issue
| The Following User Says Thank You to dirkvl For This Useful Post: | ||
|
|
2014-04-02
, 15:44
|
|
Posts: 1,104 |
Thanked: 5,652 times |
Joined on Feb 2010
@ Holland
|
#680
|
8 on the mail tomorrow!
Jouni, Jesse, Teemu, Harri (2x), Tuomo, Martin, Florian
exams on monday and tuesday, then moar assembling!
Last edited by dirkvl; 2014-04-02 at 15:54.
Jouni, Jesse, Teemu, Harri (2x), Tuomo, Martin, Florian
exams on monday and tuesday, then moar assembling!
Last edited by dirkvl; 2014-04-02 at 15:54.
 |
| Tags |
| keyboard, limited-edition, otherhalf, qwerty |
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
|
All times are GMT. The time now is 23:09.
however:
-phone only reads nfc after pin is inserted in the back (giggety?)
-the nfc reader does not has this range afaik
so... what would be the way to go now is:
-activate keyboard when malliit is opened
-to force landscape and minimize on-screen keyboard on key-press