Page 2 of 3 1 2 3
Reply
Thread Tools
hardkorek is offline hardkorek
2010-12-15 , 13:46
Posts: 186 | Thanked: 79 times | Joined on Feb 2010
#11
Great, thank you. I'll test it right now.

Update:

I tested it. I was also able to insert module but i have following errors:

Highspeed

Code:
[ 1193.618743] usbcore: registered new interface driver dm9601
[ 1218.436950] kb_lock (GPIO 113) is now closed
[ 1218.617126] kb_lock (GPIO 113) is now open
[ 1230.236175] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[ 1237.265350] Forced hostmode error: no device attached
[ 1237.265441] usb usb1: usb resume
[ 1237.288513] hub 1-0:1.0: hub_resume
[ 1237.288574] hub 1-0:1.0: port 1: status 0101 change 0001
[ 1237.397735] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 1237.397796] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 1237.522705] usb 1-1: new high speed USB device using musb_hdrc and address 2
[ 1237.647796] usb 1-1: device descriptor read/64, error -71
[ 1237.882171] usb 1-1: device descriptor read/64, error -71
[ 1238.116577] usb 1-1: new high speed USB device using musb_hdrc and address 3
[ 1238.241546] usb 1-1: device descriptor read/64, error -71
[ 1238.475982] usb 1-1: device descriptor read/64, error -71
[ 1238.710296] usb 1-1: new high speed USB device using musb_hdrc and address 4
[ 1239.132110] usb 1-1: device not accepting address 4, error -71
[ 1239.257354] usb 1-1: new high speed USB device using musb_hdrc and address 5
[ 1239.679077] usb 1-1: device not accepting address 5, error -71
[ 1239.679199] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1239.679260] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 1239.679321] hub 1-0:1.0: port 1 enable change, status 00000501
Full speed:

Code:
[ 2134.070220] WARNING: at /home/builder2/maemo-fremantle-armel-extras-devel/work/kernel-power-2.6.28/drivers/usb/musb/musb_host.c:128 musb_h_tx_flush_fifo+0x94/0xcc()
[ 2134.070281] Could not flush host TX0 fifo: csr: 000a
[ 2134.070281] Modules linked in: dm9601 usbnet vfat fat sd_mod scsi_mod iphb rfcomm panic_info_buff sco l2cap ext3 omaplfb jbd pvrsrvkm bridgedriver ipv6 g_file_storage uinput board_rx51_camera et8ek8 omap_previewer_hack omap34xxcam_mod isp_mod iovmm videobuf_dma_sg videobuf_core omap3_iommu iommu2 iommu dspbridge mmc_block ssi_mcsaab_imp phonet cmt_speech omap_hsmmc wl12xx smc91x mii omap_ssi omap_wdt hci_h4p mmc_core nokia_av mac80211 tsc2005 crc7 bluetooth fmtx_si4713 ad5820 rtc_twl4030 lis302dl videodev v4l1_compat compat_ioctl32 leds_twl4030_vibra leds_lp5523 adp1653 smia_sensor twl4030_wdt tsl2563 led_class rtc_core smiaregs v4l2_int_device joydev cifs
[ 2134.070861] [<c0030470>] (dump_stack+0x0/0x14) from [<c0057444>] (warn_slowpath+0x64/0x80)
[ 2134.070953] [<c00573e0>] (warn_slowpath+0x0/0x80) from [<c01e9a60>] (musb_h_tx_flush_fifo+0x94/0xcc)
[ 2134.071044]  r3:00000000 r2:c0349b67
[ 2134.071075]  r6:d80ab100 r5:0000000a r4:0000000a
[ 2134.071105] [<c01e99cc>] (musb_h_tx_flush_fifo+0x0/0xcc) from [<c01ea930>] (musb_cleanup_urb+0xc0/0x10c)
[ 2134.071197] [<c01ea870>] (musb_cleanup_urb+0x0/0x10c) from [<c01eb134>] (musb_urb_dequeue+0x1dc/0x248)
[ 2134.071258] [<c01eaf58>] (musb_urb_dequeue+0x0/0x248) from [<c01cec9c>] (unlink1+0x108/0x114)
[ 2134.071319] [<c01ceb94>] (unlink1+0x0/0x114) from [<c01cfc38>] (usb_hcd_unlink_urb+0x9c/0xf8)
[ 2134.071411] [<c01cfb9c>] (usb_hcd_unlink_urb+0x0/0xf8) from [<c01d0af4>] (usb_kill_urb+0x84/0x14c)
[ 2134.071472]  r7:cdf44900 r6:cdf44900 r5:cf0a6000 r4:00000000
[ 2134.071533] [<c01d0a70>] (usb_kill_urb+0x0/0x14c) from [<c01d1d78>] (usb_start_wait_urb+0x80/0x120)
[ 2134.071594]  r6:00001388 r5:cf0a7e50 r4:00000000
[ 2134.071655] [<c01d1cf8>] (usb_start_wait_urb+0x0/0x120) from [<c01d1ff8>] (usb_control_msg+0xc4/0xe8)
[ 2134.071716] [<c01d1f34>] (usb_control_msg+0x0/0xe8) from [<c01cacec>] (hub_port_init+0x3d8/0x634)
[ 2134.071807] [<c01ca914>] (hub_port_init+0x0/0x634) from [<c01cc3e4>] (hub_events+0x86c/0xe64)
[ 2134.071868] [<c01cbb78>] (hub_events+0x0/0xe64) from [<c01ce034>] (hub_thread+0x30/0x19c)
[ 2134.071929] [<c01ce004>] (hub_thread+0x0/0x19c) from [<c006da90>] (kthread+0x54/0x80)
[ 2134.071990]  r6:00000000 r5:c01ce004 r4:00000000
[ 2134.072052] [<c006da3c>] (kthread+0x0/0x80) from [<c005a950>] (do_exit+0x0/0x7bc)
[ 2134.072113]  r5:00000000 r4:00000000
[ 2134.072143] ---[ end trace 605768102227b096 ]---
[ 2134.082702] usb 1-1: khubd timed out on ep0out len=0/0
[ 2136.764282] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[ 2136.944580] usb 1-1: device not accepting address 4, error -71
[ 2136.944671] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2136.944732] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 2136.944763] hub 1-0:1.0: port 1 enable change, status 00000501
[ 2137.157714] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 2137.157775] hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 2137.311767] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 2137.436859] usb 1-1: new full speed USB device using musb_hdrc and address 5
[ 2137.585235] usb 1-1: ep0 maxpacket = 8
[ 2137.586242] usb 1-1: default language 0x0409
[ 2137.588104] usb 1-1: uevent
[ 2137.588287] usb 1-1: usb_probe_device
[ 2137.588348] usb 1-1: configuration #1 chosen from 1 choice
[ 2137.594024] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2137.594390] usb 1-1:1.0: uevent
[ 2137.596038] /home/builder2/maemo-fremantle-armel-extras-devel/work/kernel-power-2.6.28/drivers/usb/core/inode.c: creating file '005'
[ 2137.596740] usb 1-1: New USB device found, idVendor=0fe6, idProduct=8101
[ 2137.596771] usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=3
[ 2137.596801] usb 1-1: Product: USB Network Controller
[ 2137.596832] usb 1-1: SerialNumber: 
[ 2137.596893] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 2137.596954] hub 1-0:1.0: port 1 enable change, status 00000103
udhcpc in both cases:
Code:
Nokia-N900:~# udhcpc 
udhcpc (v0.9.9-pre) started
SIOCGIFINDEX failed!: No such device
Last edited by hardkorek; 2010-12-15 at 18:18.
 
blue_led is offline blue_led
2010-12-15 , 18:48
Posts: 306 | Thanked: 566 times | Joined on Jan 2010 @ Romania
#12
according datasheet davicom dm9601 is full speed device
start with davicom adapter plugged to n900

try
echo -1 >/sys/module/usbcore/parameters/autosuspend
or
echo 2 >/sys/module/usbcore/parameters/autosuspend
Last edited by blue_led; 2010-12-15 at 19:20.
 
hardkorek is offline hardkorek
2010-12-17 , 10:15
Posts: 186 | Thanked: 79 times | Joined on Feb 2010
#13
Code:
[10468.066375] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[10469.498474] usb usb1: usb resume
[10469.515258] hub 1-0:1.0: hub_resume
[10469.515350] hub 1-0:1.0: port 1: status 0101 change 0001
[10469.624938] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[10469.624969] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[10469.750305] usb 1-1: new full speed USB device using musb_hdrc and address 26
[10474.749877] usb 1-1: khubd timed out on ep0in len=0/64
[10479.749694] usb 1-1: khubd timed out on ep0in len=0/64
[10484.749755] usb 1-1: khubd timed out on ep0in len=0/64
[10484.874694] usb 1-1: device descriptor read/64, error -110
[10489.984100] usb 1-1: khubd timed out on ep0in len=0/64
Nokia-N900:~# cat /sys/module/usbcore/parameters/autosuspend
-1
-----------------------------------------------------------
Nokia-N900:/dev# ls | grep usb
usbdev1.1_ep00
usbdev1.1_ep81
usbmon0
usbmon1
-----------------------------------------------------------
Nokia-N900:/dev# ls /sys/class/net
lo        phonet0   wlan0     wmaster0
-----------------------------------------------------------
Nokia-N900:/dev# ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3755 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3755 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:220825 (215.6 KiB)  TX bytes:220825 (215.6 KiB)

phonet0   Link encap:UNSPEC  HWaddr 15-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          UP POINTOPOINT RUNNING NOARP  MTU:4000  Metric:1
          RX packets:7226 errors:0 dropped:0 overruns:0 frame:0
          TX packets:881 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:526868 (514.5 KiB)  TX bytes:42504 (41.5 KiB)

wlan0     Link encap:Ethernet  HWaddr 34:7E:39:4A:47:F2  
          inet addr:192.168.1.102  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::367e:39ff:fe4a:47f2/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:9953 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7796 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:9743450 (9.2 MiB)  TX bytes:903025 (881.8 KiB)

wmaster0  Link encap:UNSPEC  HWaddr 00-1F-DF-57-C9-2E-00-00-00-00-00-00-00-00-00-00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
It's still not creating interface.
 
shadowjk is offline shadowjk
2010-12-21 , 14:01
Posts: 1,258 | Thanked: 672 times | Joined on Mar 2009
#14
I have a davicom, and it's basically useless and unstable even when you use it with a PC.
 
chris102 is offline chris102
2011-01-03 , 20:17
Posts: 10 | Thanked: 3 times | Joined on Jan 2011
#15
Hi,

fyi:

i have a apple usb ethernet adapter... anyway i have the same problem... i asked in another thread for help with a displaylink driver which is usb as well... sadly i cannot get it to work. So you're not alone... :-(

Code:
[92365.538391] usb 1-1.4: New USB device found, idVendor=05ac, idProduct=1402
[92365.538421] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[92365.538452] usb 1-1.4: Product: Apple USB Ethernet Adapter
[92365.538452] usb 1-1.4: Manufacturer: Apple Inc.      
[92365.538452] usb 1-1.4: SerialNumber: 024D35
[92494.863952] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0004
[92494.874938] hub 1-1:1.0: port 2, status 0101, change 0001, 12 Mb/s
[92495.031433] hub 1-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[92495.117370] usb 1-1.2: new high speed USB device using musb_hdrc and address 28
[92495.228637] usb 1-1.2: default language 0x0409
[92495.231414] usb 1-1.2: uevent
[92495.231628] usb 1-1.2: usb_probe_device
[92495.231658] usb 1-1.2: configuration #1 chosen from 1 choice
[92495.237030] usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
[92495.237365] usb 1-1.2:1.0: uevent
[92495.238647] /home/builder2/maemo-fremantle-armel-extras-devel/work/kernel-power-2.6.28/drivers/usb/core/inode.c: creating file '028'

i think it will be required to compile an own kernel... :-(

It looks like nobody really cares about arm when writing modules/drivers... t've seen this problem often now...
 
chris102 is offline chris102
2011-01-03 , 20:18
Posts: 10 | Thanked: 3 times | Joined on Jan 2011
#16
anyway i continue to work on it and keep you updated...
 

The Following 2 Users Say Thank You to chris102 For This Useful Post:
biketool is offline biketool
2011-06-24 , 13:33
Posts: 1,431 | Thanked: 2,630 times | Joined on Jan 2011 @ Touring
#17
Has anyone gotten this device to work?
I have also posted here http://talk.maemo.org/showpost.php?p...&postcount=268
I have a davicom chipped Crystal Blue super cheap USB wired ethernet adapter that I can almost get working on my N900. I have in the past installed some scripts to try to get this working but the USB port was broken so I wasn't able to get anything working.
Now with a new USB port I have read/write on flash drives, I can use USB keyboards, I also can get the Crystal Blue ethernet adapter to light up and an interface called WIRED appears in my Internet connections options and automatically attempts to give my programs Internet access unsuccessfully.
The driver seems to be available for the Davicom, but none loads and then obviously no interface appears in ifconfig.
I am having trouble finding definite info other than the os2008 stuff which obviously will not work with a N900.
I run /usr/sbin/usbEthUp.sh and it says that /lib/modules/2.6.28.10-power47/usb2net/modlist is not present
Is there a USB ethernet adapters faq like they did for os2008 that I am missing?
I know the davicom chip is flaky but this adapter successfully connects when used with my laptop.
tried sudo modprobe usbnet, no love at all.
I am sure I am missing something stupid and this is a few keystrokes away for someone who actually knows what is going on.
I also looked at http://talk.maemo.org/showthread.php?p=1002480 and didn't see anything useful, again perhaps overlooking the obvious.
 
Estel's Avatar
Estel is offline Estel
2011-06-24 , 13:40
Posts: 5,028 | Thanked: 8,613 times | Joined on Mar 2011
#18
Don't quote me on that cause this is pure guess working, but may:

I run /usr/sbin/usbEthUp.sh and it says that /lib/modules/2.6.28.10-power47/usb2net/modlist
...mean that module is missing from kernel and You must ask pali to include it in next kernel release? You're using kp47, right?
 

The Following User Says Thank You to Estel For This Useful Post:
biketool is offline biketool
2011-06-25 , 19:22
Posts: 1,431 | Thanked: 2,630 times | Joined on Jan 2011 @ Touring
#19
Originally Posted by Estel View Post
Don't quote me on that cause this is pure guess working, but may:



...mean that module is missing from kernel and You must ask pali to include it in next kernel release? You're using kp47, right?
Probably right although I had thought that the compiled module was floating around here on talk at some point, it was a few months that I couldn't hack because of a broken USB but now that I am back I can't find them if they were the right ones anyways.
Forgive my ignorance is Pali the powerkernel maintainer?
thanks
 
Estel's Avatar
Estel is offline Estel
2011-06-25 , 20:00
Posts: 5,028 | Thanked: 8,613 times | Joined on Mar 2011
#20
Ya, it's Pali, but for best results I recommend You to ask for that in kp47 thread:
http://talk.maemo.org/showthread.php?t=71879

Many skilled people read this thread, so You got higher chances that someone will mention useful things.
 
Reply
Page 2 of 3 1 2 3

« Previous Thread | Next Thread »
Thread Tools

 
Forum Jump


All times are GMT. The time now is 08:06.

Contact Us - Home - Archive - Top