Page 58 of 129 « First 485657 58 596068 Last »
Reply
Thread Tools
ssjmec is offline ssjmec
2012-05-04 , 09:41
Posts: 130 | Thanked: 17 times | Joined on Dec 2011
#571
Originally Posted by itsnotabigtruck View Post
The GUI doesn't automatically boost the voltage (and I'm not sure the current version of the modules does either) - dial it into the voltage you want and set it to that.

Note that you should make sure to set the voltage to the absolute lowest stable value for the clock speed you want. High voltages cause electromigration in the chip (= shorter device lifetime), high heat output (= overly toasty phone), and high power consumption (= low battery life). You'll need to incrementally lower the voltage and run a stress test until it starts crashing, at which point it should be raised to the last stable value.
Yup just knew it. I just thought that it would automatically voltage up just like before without UI. thanks for answering nicely
 
besttt is offline besttt
2012-05-04 , 10:06
Posts: 151 | Thanked: 38 times | Joined on May 2012
#572
now iam at 1 hour at 1400 mhz 1412500 voltage play radio web browsing send mesages so far so good sr off
 
koe is offline koe
2012-05-04 , 11:06
Posts: 58 | Thanked: 21 times | Joined on Mar 2012
#573
Originally Posted by besttt View Post
now iam at 1 hour at 1400 mhz 1412500 voltage play radio web browsing send mesages so far so good sr off
i have very much lag with this settings.
 
besttt is offline besttt
2012-05-04 , 11:10
Posts: 151 | Thanked: 38 times | Joined on May 2012
#574
it failed i think the safest is 1375000 voltage with all frequency 1300-1400 with sr off
 
besttt is offline besttt
2012-05-04 , 14:07
Posts: 151 | Thanked: 38 times | Joined on May 2012
#575
all voltage above 1375000 failed with all frequency but i think the phone is faster only above 1375000 voltage
 
itsnotabigtruck is offline itsnotabigtruck
2012-05-04 , 15:18
Posts: 245 | Thanked: 915 times | Joined on Feb 2012
#576
Originally Posted by asianmoomoo View Post
WOW. i did it! Thanks for the help Creamy Goodness.

now that i did this, do i need to incept it everytime i want to change the speed?

also, for the voltage - i understand is the balance between that and the speed...do you recommend the best speed + voltage for battery life and increase in speed?

i would imagine dropping the voltage to like 100000...
Once OPPtimizer is installed and working, you don't have to use pasiv or incept again - you can simply launch it from the home screen.
__________________
 
asianmoomoo is offline asianmoomoo
2012-05-04 , 15:49
Posts: 115 | Thanked: 30 times | Joined on Jun 2007
#577
i am currently at 1200mhz and 1200000 voltage.


i am debating if i should do 1200/ 1275000
 
ibrakalifa's Avatar
ibrakalifa is offline ibrakalifa
2012-05-04 , 16:11
Posts: 1,583 | Thanked: 1,203 times | Joined on Dec 2011 @ Everywhere
#578
1,35ghz @130000
__________________
~$
~#
 
Sniper_swe is offline Sniper_swe
2012-05-04 , 16:16
Posts: 362 | Thanked: 179 times | Joined on Sep 2010
#579
Originally Posted by Creamy Goodness View Post
btw, check this out, the thing to read the temperature from the cpu is already on the phone:
opensh
modprobe omap34xx_temp
cat /sys/devices/platform/omap34xx_temp/temp1_input
Doesn't work very good though. It seems to stop working after a few times for me.
gives me sh: modprobe: not found
Suggestions?
 
Creamy Goodness is offline Creamy Goodness
2012-05-04 , 16:38
Posts: 1,463 | Thanked: 1,916 times | Joined on Feb 2008 @ Edmonton, AB
#580
/sbin/modprobe
texas instruments screwed up that sensor apparently, so it's not likely to work properly. Stupid company.
__________________
Last edited by Creamy Goodness; 2012-05-04 at 16:40.
 

The Following User Says Thank You to Creamy Goodness For This Useful Post:
Reply
Page 58 of 129 « First 485657 58 596068 Last »

« Previous Thread | Next Thread »
Thread Tools

 
Forum Jump


All times are GMT. The time now is 00:23.

Contact Us - Home - Archive - Top