[120003.890625] usb 1-1: usb_disable_device nuking all URBs
[120003.890625] usb 1-1: unregistering interface 1-1:1.0
[120003.890625] usbdev1.3_ep81: ep_device_release called for usbdev1.3_ep81
[120003.890625] usbdev1.3_ep02: ep_device_release called for usbdev1.3_ep02
[120003.890625] usb 1-1:1.0: uevent
[120003.890625] usbdev1.3_ep00: ep_device_release called for usbdev1.3_ep00
[120003.890625] usb 1-1: uevent
[120004.023437] scsi 1:0:0:0: rejecting I/O to dead device
[120004.023437] scsi 1:0:0:0: rejecting I/O to dead device
[120004.039062] scsi 1:0:0:0: rejecting I/O to dead device
[120004.039062] scsi 1:0:0:0: rejecting I/O to dead device
[120004.039062] scsi 1:0:0:0: rejecting I/O to dead device
[120004.039062] scsi 1:0:0:0: rejecting I/O to dead device
[120005.890625] hub 1-0:1.0: hub_suspend
[120005.890625] usb usb1: usb auto-suspend
[120153.250000] EAC mode: play enabled, rec enabled
[120155.953125] EAC mode: play disabled, rec disabled
[120174.671875] menelaus 1-0072: Setting voltage 'VMMC' to 3000 mV (reg 0x0a, val 0xb8)
[120179.687500] menelaus 1-0072: Setting voltage 'VMMC' to 3000 mV (reg 0x0a, val 0xb8)
[120200.515625] EAC mode: play enabled, rec enabled
[120203.406250] EAC mode: play disabled, rec disabled
[125719.320312] tusb_source_power 629: VBUS a_wait_vrise, devctl 81 otg 184 conf c0010001 prcm 00a80500
[125719.593750] musb_stage0_irq 646: CONNECT (a_host) devctl 5d
[125719.593750] hub 1-0:1.0: state 8 ports 1 chg 0000 evt 0000
[125719.593750] usb usb1: usb auto-resume
[125719.593750] usb usb1: finish resume
[125719.593750] hub 1-0:1.0: hub_resume
[125719.617187] hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[125719.773437] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[125719.898437] usb 1-1: new high speed USB device using musb_hdrc and address 4
[125720.070312] usb 1-1: default language 0x0409
[125720.070312] usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
[125720.070312] usb 1-1: Product: USB Mass Storage Device
[125720.070312] usb 1-1: Manufacturer: TSST corp
[125720.070312] usb 1-1: SerialNumber: SET084MP00000002A01
[125720.070312] usb 1-1: device v0409 p0840 is not supported
[125720.070312] usb 1-1: uevent
[125720.070312] usb 1-1: usb_probe_device
[125720.070312] usb 1-1: configuration #1 chosen from 1 choice
[125720.570312] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[125720.578125] usb 1-1:1.0: uevent
[125720.578125] usb-storage 1-1:1.0: usb_probe_interface
[125720.578125] usb-storage 1-1:1.0: usb_probe_interface - got id
[125720.593750] scsi2 : SCSI emulation for USB Mass Storage devices
[125720.601562] drivers/usb/core/inode.c: creating file '004'
[125720.601562] hub 1-0:1.0: 198mA power budget left
[125720.601562] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[125720.601562] hub 1-0:1.0: port 1 enable change, status 00000503
[125720.601562] usb-storage: device found at 4
[125720.601562] usb-storage: waiting for device to settle before scanning
[125724.359375] EAC mode: play enabled, rec enabled
[125725.617187] scsi 2:0:0:0: CD-ROM TSSTcorp CD/DVDW SE-T084L TS00 PQ: 0 ANSI: 0
[125726.242187] sr0: scsi3-mmc drive: 6x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[125726.242187] sr 2:0:0:0: Attached scsi CD-ROM sr0
[125726.242187] sr 2:0:0:0: Attached scsi generic sg0 type 5
[125726.265625] usb-storage: device scan complete
[125727.062500] EAC mode: play disabled, rec disabled
[125828.945312] menelaus 1-0072: Setting voltage 'VMMC' to 3000 mV (reg 0x0a, val 0xb8)
[125833.960937] menelaus 1-0072: Setting voltage 'VMMC' to 3000 mV (reg 0x0a, val 0xb8)
[125904.039062] EAC mode: play enabled, rec enabled
[125906.742187] EAC mode: play disabled, rec disabled

It all looks good so far

Can you try the mount again and paste any output here?

if it fails, also in xterm type

mount

and paste the output here

Pls see following result:

/home/user # mount
rootfs on / type rootfs (rw)
/dev/root on /mnt/initfs type jffs2 (ro)
none on /mnt/initfs/proc type proc (rw)
none on /mnt/initfs/sys type sysfs (rw)
none on /mnt/initfs/tmp type tmpfs (rw)
/dev/mtdblock4 on / type jffs2 (rw,rpsize=1024,rpuid=0,rpuid=30000)
none on /tmp type tmpfs (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
none on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
/dev/mmcblk0p1 on /media/mmc2 type vfat (rw,nosuid,nodev,noexec,uid=29999,fmask=0133 ,dmask=0000,codepage=cp437,iocharset=iso8859-1,shortname=mixed,utf8)
/dev/mmcblk1p1 on /media/mmc1 type vfat (rw,nosuid,nodev,noexec,uid=29999,fmask=0133 ,dmask=0000,codepage=cp437,iocharset=iso8859-1,shortname=mixed,utf8)

You did not paste the mount command that is failing for you. What happens when you actually try to mount it, wheat error are you getting?

I've already paste, pls see
/usr/lib # mount /dev/scd0 /root/mmnt -t iso9660
mount: mounting /dev/scd0 on /root/mmnt failed
/usr/lib # mount /dev/scd0 /root/mmnt -t udf
mount: mounting /dev/scd0 on /root/mmnt failed

Hi guys, I've just few minutes ago inserted audio cd in my cdrom and connected it to n800. The folder named scd0 appeared in file manager, but unfortunately there is no any data in this folder.
Could you pls help me to connect and use cdrom on my tablet

Congratulations, I connected cdrom to my n800.
.
It was done after simple action, I created folder mmnt in /root in mc.
.
So now I can use all the data I have on my cds ))))

Penguinbait i installed cdrom.deb but tell me what is http://penguinbait.com/modules.tar and i need to add them to my n800 os2008 device??

hi, i have problem with my usb cdrom (cdwriter), i installed .deb, modules are loaded

here is my lsmod:
udf 84964 0 - Live 0xbf077000
isofs 32092 0 - Live 0xbf06e000
sr_mod 13444 0 - Live 0xbf069000
sg 21592 0 - Live 0xbf062000
cdrom 35164 1 sr_mod, Live 0xbf058000
g_file_storage 27560 0 - Live 0xbf050000
cx3110x 56200 0 - Live 0xbf041000
umac 258788 1 cx3110x, Live 0xbf000000 (P)

when i attach cdrom the device in /dev doesnt create, here is part of dmesg:
[ 673.242187] usb 1-1: new full speed USB device using musb_hdrc and address 2
[ 673.375000] usb 1-1: ep0 maxpacket = 16
[ 673.375000] usb 1-1: default language 0x0409
[ 673.375000] usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
[ 673.375000] usb 1-1: Product: HP USB CD-Writer Plus
[ 673.375000] usb 1-1: device v03f0 p0207 is not supported
[ 673.375000] usb 1-1: uevent
[ 673.375000] usb 1-1: usb_probe_device
[ 673.375000] usb 1-1: configuration #1 chosen from 1 choice
[ 673.375000] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 673.375000] usb 1-1:1.0: uevent
[ 673.375000] usbtest 1-1:1.0: usb_probe_interface
[ 673.375000] usbtest 1-1:1.0: usb_probe_interface - got id
[ 673.382812] drivers/usb/core/inode.c: creating file '002'
[ 673.382812] hub 1-0:1.0: 200mA power budget left
[ 673.382812] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 673.382812] hub 1-0:1.0: port 1 enable change, status 00000103
[ 675.382812] usb 1-1: usb auto-suspend
[ 677.406250] hub 1-0:1.0: hub_suspend
[ 677.406250] usb usb1: usb auto-suspend


does anybody know how to fix it? it works well with my linux laptop..thanks

Someone should make a mini portable CD reader/writer... you know, one that would just use the small format discs. That would go really well with my N810...