![]() |
2010-04-24
, 08:09
|
Banned |
Posts: 3,412 |
Thanked: 1,043 times |
Joined on Feb 2010
|
#211
|
![]() |
2010-04-24
, 08:54
|
Posts: 248 |
Thanked: 240 times |
Joined on Mar 2010
@ Wiltshire, UK
|
#212
|
![]() |
2010-04-24
, 09:34
|
Posts: 5,795 |
Thanked: 3,151 times |
Joined on Feb 2007
@ Agoura Hills Calif
|
#213
|
@shadowjk:
I stand corrected, of course.
The terms 'charger' are generically but incorrectly used by the manufacturer and users alike. I followed that mistaken use of the word.
To those who don't know: the software in the 'phone manages battery charging by monitoring battery voltage and other data This facilitates a faster charging rate up to a safe point and thereafter a prolonged but typically limited trickle-charge. The 'charger' is really a transformer that supplies a constant voltage and charge rate.
Cheap 'desktop chargers' often claim to have similar charging ciruitry, but I would not rely on that. NEVER leave batteries on a desktop/trickle charger for more than a few hours at a time and regard them as backup charger only.
Keep the charger away from paper/other flammable materials and monitor battery temperature throughout the charge process. Perform as much charging via the phone as possible - this is your best policy for prolonged and safe battery life.
Store batteries in a cool, dark space and if they get cold warm them very gently before charging. Never carry exposed batteries in your pocket - the contacts could be shorted out. Use/rotate spare batteries to ensure their voltage does not drop too far as this may result in a 'dead' battery that cannot be re-charged.
I hope this clarifies the matter and am indebted to shadowjk for pointing out the shortfalls in my Quick Reply - these are important matters.
![]() |
2010-04-24
, 10:23
|
Posts: 1,258 |
Thanked: 672 times |
Joined on Mar 2009
|
#214
|
![]() |
2010-04-24
, 10:36
|
Posts: 5,795 |
Thanked: 3,151 times |
Joined on Feb 2007
@ Agoura Hills Calif
|
#215
|
Typically these desktop chargers are built using emergency battery protection chips. They're meant as second line of defense in case the primary charging circuitry fails, or if the device doesn't shut down by itself before battery becomes empty. Because they're not meant to actually have to do anything in normal use, their trip points are set outside the typical operating range of the battery.
In the long run this stresses the battery, making its capacity decay much more rapidly than normal.
![]() |
2010-04-28
, 12:52
|
Posts: 14 |
Thanked: 1 time |
Joined on Apr 2010
|
#216
|
![]() |
2010-04-28
, 16:07
|
Posts: 1,341 |
Thanked: 708 times |
Joined on Feb 2010
|
#217
|
![]() |
2010-04-28
, 16:24
|
|
Posts: 2,050 |
Thanked: 1,425 times |
Joined on Dec 2009
@ Bucharest
|
#218
|
![]() |
2010-04-28
, 16:27
|
|
Posts: 2,142 |
Thanked: 2,054 times |
Joined on Dec 2006
@ Sicily
|
#219
|
![]() |
2010-04-28
, 16:41
|
Posts: 1,341 |
Thanked: 708 times |
Joined on Feb 2010
|
#220
|
Also, I was hoping for a flat cover, flush with the camera. Now it just looks overweight.
How did you manage to have a nicely descending battery bar graph? My battery status bar widget stays at 8 bars until the Mugen battery is dry, when it goes straight to the zero level.
The Following User Says Thank You to zimon For This Useful Post: | ||