just plug it out and manually boot it...

Now it is stuck on the "Nokia Logo" and it reboots :'(

ohh btw on the navifirm my version "059L8L7" comes only in 20.2011.40.4 and 10.2011.34.1 i tried the 20.2011.40.4 version was that okay?

and now after some reboots the previous "too many reboots" is back

so heres the thing ... i looked over the internet to see if i was flashing it right and people have this blue bar immediatly after they flashed ... it appeared on my screen but it disappears after the first second :/

Can you post the otput of the flasher command, does it indicate any errors in the flashing process?

Hour I lost IMEI (* # 06 # not seen), the wave is lost. Flash by Flasher and 4ever also not been. Who knows up FW by Phoniex or Nokia BEST sure to help you with? Thanks
the version of your FW 4 ...... PR.454.


help me

I also faced this issue and finally sent my N9 to service center.
But you can try to download fw files for product code which is mentioned at back of SIM card tray.
Check first post which talks about recovering from flash errors.
These errors are related to cellular modem files.

My nokia N9(switzerland – 059k748) turned off by itself one fine day and it went into a boot-loop(starts up with nokia logo and turns off, and that keeps going on like that). Then i thought of flashing the device. I used Navifirm 1.7 to download the respective firmware for my device. Then using flasher 3.12.1 i tried flashing it. But im getting errors in the process. i tried several times re-downloading the firmware and flashing again. I have even tried flashing it with another country specific firmware but had no luck. All i see from the first place now is a warning screen when the phone is started up or is plugged into the usb port.

Here is the error screen i see:

WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting…
USB device found at bus 002, device address 045.
Device identifier: 357923041060460 (SN: N/A)
Found device RM-696, hardware revision 1507
NOLO version 2.3.6
Version of ‘sw-release’: DFL61_HARMATTAN_40.2012.21-3_PR_009
Sending ape-algo image (7096 kB)…
100% (7096 of 7096 kB, avg. 31125 kB/s)
Suitable USB interface (phonet) not found, waiting…
USB device found at bus 002, device address 046.
Device identifier: 357923041060460 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_009
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped

Battery level 80 %, continuing.

image [state progress transfer flash speed]
———————————————————————
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[_] cmt-mcusw [finishing 25 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1971 kB/s]
[_] rootfs [finishing 100 % 32768 / 1170206 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
———————————————————————
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1971 kB/s]
[f] rootfs [finishing 0 % 32768 / 1170206 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not exec ‘tune2fs -L rootfs /tmp/sudmmcGDmzw0/internal0p2′
mmc: Could not remove mount directory /tmp/sudmmcGDmzw0/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images

I have tried this on both windows as well as on linux and get the same result. Any help from anyone is greatly appreciated.

Thanks in advance

H2O,

I'm not 100% sure but iirc that error requires emmc being flashed too or your previous firmware's cmt-mcusw being flashed.

If its emmc you may want to take out all your data first by mounting the phone using juiceme's telnet

Maybe do a bit of searching on this thread your error may have happened to someone else before...

I have tried that as well infact. I have individually tried all the following command to see if atleast one works:

1. flasher -F main.bin -f
2. flasher -F main.bin -F emmc.bin -f (with -R as well)
3. flasher -F main.bin -f --flash-only=rootfs, cmt (arguments taken individually as well)

No clue on what to do now. Thanks anyways