Active Topics

 


Page 9 of 11 « First 78 9 1011
Reply
Thread Tools
wred_e is offline wred_e
2014-02-21 , 15:00
Posts: 18 | Thanked: 16 times | Joined on Aug 2012 @ Åbo, Finland
#81
Bought some copper tape, if anybody in Turku needs some then just write me a message. I found it hard to find in the stores..
 
Silwer is offline Silwer
2014-02-22 , 12:47
Posts: 231 | Thanked: 143 times | Joined on Feb 2012 @ Tallinn, Estonia
#82
Originally Posted by Silwer View Post
I just received my two sets of Touchstone charger pads and receivers. Installed one receiver to my white and other to my poppy red other half.

However, I have problems. First - every second or two I am receiving charging notifications and it is very annoing.

Second issue is that while charging either charger or receiver is making quiet, but still clearly audiable electrical whining noise. Is it normal?

These issues I have with my both sets of receivers / chargers. I am using 1A charger connected to the Touchstone pad. Any suggestions?

EDITED:
Checked with CSD tool and it is not charging. It just circulates between "Full" and "Discharging". However, battery level is only at 21%.

EDITED2: Somehow problems just solved by themselves. No noise and it is charging now properly. Do not know, what the issue was.
Problem was in the chargers. I bought two cheap chargers from ebay that were rated 2A. Actually their output was about 0,15A less than Nokia N9 original charger that is rated 1A (measured with CSD tool). I also tried my other chargers that were rated 0,5A and 0,65A. These were not sufficient to provide charging through Touchstone kit (charging did not start at all). Now, using Nokia N9 1A chargers all works fine. Therefore - when choosing a Touchstone kit, make sure that your charger is able to output at least 1A as otherwise it just wont work properly.
 

The Following User Says Thank You to Silwer For This Useful Post:
yjeanrenaud is offline yjeanrenaud
2014-04-28 , 21:48
Posts: 4 | Thanked: 2 times | Joined on Feb 2014
#83
Originally Posted by Kaacz View Post
Ok, I make own.
Bought this on eBay.

Polarity is easy exchanged by shift power strip (on naked receiver).
No need to make crossing as made @Wonko.
The spacing between contacts is reduced by cut with scissors.

When charger pad is powered by standard Jolla 1A power adapter, phone is charged by 550-600mA in good position on charger pad.
But on charger pad is info: Input 5V 2A, Output 5V 1A ..

And result in more images.
great! how did you get rid of the golden connectors?
 
juju_des_highlands is offline juju_des_highlands
2014-05-01 , 10:41
Posts: 1 | Thanked: 1 time | Joined on May 2014
#84
Originally Posted by Bundyo View Post
Touchstone setup takes about 10 mins along with the time needed for detaching the coil and electronics from the Palm cover. Used a short adhesive copper band for connections.
Originally Posted by Wonko View Post
First of all, thanks a lot rainisto for your work and for posting it here.

I attached some photos of the internals and of the phone on the touchstone charger.
Personally, I quite like the "floating look" of the device when it is attached to the charger.
Hi!
Could one of you tell me if charging works through a case for example?
I saw some Qi chargers working though 5mm so it would be great for me, I don't want to have to take my lastucase off for charging if possible.
Thanks!
 

The Following User Says Thank You to juju_des_highlands For This Useful Post:
Bundyo's Avatar
Bundyo is offline Bundyo
2014-05-02 , 22:06
Posts: 4,708 | Thanked: 4,649 times | Joined on Oct 2007 @ Bulgaria
#85
Not sure, but probably not (at least with the touchstone) - additionally the magnets probably won't work too.
__________________
Technically, there are three determinate states the cat could be in: Alive, Dead, and Bloody Furious.
 

The Following User Says Thank You to Bundyo For This Useful Post:
yjeanrenaud is offline yjeanrenaud
2014-06-19 , 16:10
Posts: 4 | Thanked: 2 times | Joined on Feb 2014
#86
since Update 1.0.7.16 I got issues while charging. Anyone else?
 

The Following 2 Users Say Thank You to yjeanrenaud For This Useful Post:
dirkvl is offline dirkvl
2014-06-19 , 16:49
Posts: 1,104 | Thanked: 5,652 times | Joined on Feb 2010 @ Holland
#87
Originally Posted by yjeanrenaud View Post
since Update 1.0.7.16 I got issues while charging. Anyone else?
not me! not charging at all? slower? on-off-on-off?
 

The Following User Says Thank You to dirkvl For This Useful Post:
Faz's Avatar
Faz is offline Faz
2014-06-19 , 17:09
Posts: 284 | Thanked: 80 times | Joined on Mar 2007 @ London, UK
#88
I have a few Funky wireless, all good here.
 
carmenluci is offline carmenluci
2014-06-23 , 21:32
Posts: 86 | Thanked: 115 times | Joined on Feb 2014 @ Spain
#89
Originally Posted by dirkvl View Post
not me! not charging at all? slower? on-off-on-off?
For me, it's not charging at all since I updated to 1.0.7.16
 
0312birdzhang is offline 0312birdzhang
2014-07-02 , 05:24
Posts: 7 | Thanked: 9 times | Joined on Jul 2014 @ Guangzhou,China
#90
Hello,I did a copy of yours,but mine do not work
Last edited by 0312birdzhang; 2014-07-02 at 05:34.
 
Reply
Page 9 of 11 « First 78 9 1011

« Previous Thread | Next Thread »

 
Forum Jump


All times are GMT. The time now is 01:27.

Contact Us - Home - Archive - Top