Active Topics
-
Firefox with Leste (10)
to Maemo 7 / Leste by teroyk - 2 days, 18 hrs ago - more...
deutch1976 |
2019-08-12
, 08:33
|
|
Posts: 701 |
Thanked: 1,981 times |
Joined on Jun 2015
@ Lisbon - Portugal
|
#1
|
Hi there. Everytime i restart the tablet i have to mannualy reconnect to my home wifi connection. I'm now on Sailfish 3.1. Is this a known issue? Thanks
| The Following User Says Thank You to deutch1976 For This Useful Post: | ||
|
|
2019-08-12
, 11:57
|
|
Posts: 807 |
Thanked: 1,589 times |
Joined on Aug 2014
|
#2
|
Originally Posted by deutch1976
This issue has been discussed before upon TJC although supposedly addressed in software update, however seemed no such issues with older WLAN:https://together.jolla.com/question/...ord-forgotten/
Hi there. Everytime i restart the tablet i have to mannualy reconnect to my home wifi connection. I'm now on Sailfish 3.1. Is this a known issue? Thanks
| The Following 2 Users Say Thank You to aspergerguy For This Useful Post: | ||
 |
|
2019-08-12
, 19:41
|
|
Posts: 6,436 |
Thanked: 12,701 times |
Joined on Nov 2011
@ Ängelholm, Sweden
|
#3
|
Check if wifi mac of your tablet is changing after each reboot or each connect to router
| The Following User Says Thank You to coderus For This Useful Post: | ||
|
|
2019-12-22
, 11:22
|
|
Posts: 106 |
Thanked: 372 times |
Joined on Jan 2012
|
#4
|
I have Aigo with the last OS update.
I have been suffering the changing WLAN MAC address.
I have applied the solution presented in
https://together.jolla.com/question/...nt-static-mac/
Sometimes it works, sometimes not (= in restart tablet may have the given WLAN MAC, sometimes not. It may be connected with the missing of "dhcpcd@wlan0.service" in the tablet.
/etc/systemd/system/changemac@.service
I removed "Before=dhcpcd@%i.service", but wondered when the service would be started then (I am not well enough aware of these things, just testing without proper knowledge).
The behavior was exactly the same as before. Is there a proper "place" in the startup (Before=), so that the change would work?
When there is different WLAN MAC after startup, it will change to given one if wlan is switched off and on. However, it does not connect to the previously worked WLAN connection as the signal strength is zero. You have to add a new connection and give new passcode to connect to wlan,
Any solution?
Last edited by Heik; 2019-12-22 at 11:32.
I have been suffering the changing WLAN MAC address.
I have applied the solution presented in
https://together.jolla.com/question/...nt-static-mac/
Sometimes it works, sometimes not (= in restart tablet may have the given WLAN MAC, sometimes not. It may be connected with the missing of "dhcpcd@wlan0.service" in the tablet.
/etc/systemd/system/changemac@.service
Code:
[Unit] Description=Change MAC address Before=dhcpcd@%i.service [Service] Type=oneshot ExecStart=/sbin/ip link set dev %i address 00:09:4c:e5:2b:a9 ExecStart=/sbin/ip link set dev %i up [Install] WantedBy=network.target
Code:
# systemctl enable changemac@wlan0 # systemctl start changemac@wlan0
The behavior was exactly the same as before. Is there a proper "place" in the startup (Before=), so that the change would work?
When there is different WLAN MAC after startup, it will change to given one if wlan is switched off and on. However, it does not connect to the previously worked WLAN connection as the signal strength is zero. You have to add a new connection and give new passcode to connect to wlan,
Any solution?
Last edited by Heik; 2019-12-22 at 11:32.
|
|
2019-12-22
, 12:56
|
|
Posts: 6,436 |
Thanked: 12,701 times |
Joined on Nov 2011
@ Ängelholm, Sweden
|
#5
|
i had the same problem on jolla tablet. you have to edit /usr/sbin/serial-from-factory-data
| The Following User Says Thank You to coderus For This Useful Post: | ||
|
|
2019-12-22
, 15:24
|
|
Posts: 106 |
Thanked: 372 times |
Joined on Jan 2012
|
#6
|
Originally Posted by coderus
So I removed (commented with #) the lines in the WLANMAC section,
i had the same problem on jolla tablet. you have to edit /usr/sbin/serial-from-factory-data
As far as I understand, running that file does not now do anything related to WLAN MAC address.
Was that the correct action? No unwanted side effects?
Seems to work now for me.
Thanks
|
|
2019-12-22
, 20:18
|
|
Posts: 6,436 |
Thanked: 12,701 times |
Joined on Nov 2011
@ Ängelholm, Sweden
|
#7
|
for myself i just placed static mac in this script instead of WLANMAC section,
|
|
2020-03-01
, 14:14
|
|
Posts: 701 |
Thanked: 1,981 times |
Joined on Jun 2015
@ Lisbon - Portugal
|
#8
|
Originally Posted by coderus
Hi there. Managed to edit file and have mac adress from tablet but where do i put it? Thanks
for myself i just placed static mac in this script instead of WLANMAC section,
|
|
2020-03-01
, 17:03
|
|
Posts: 6,436 |
Thanked: 12,701 times |
Joined on Nov 2011
@ Ängelholm, Sweden
|
#9
|
just replace /usr/bin/txeireader with following script and make it executable: https://gist.github.com/CODeRUS/178d...43318cbbfbae33
|
|
2020-03-01
, 18:31
|
|
Posts: 701 |
Thanked: 1,981 times |
Joined on Jun 2015
@ Lisbon - Portugal
|
#10
|
Originally Posted by coderus
So there is no need to change the other file? How to turn this one executable?
just replace /usr/bin/txeireader with following script and make it executable: https://gist.github.com/CODeRUS/178d...43318cbbfbae33