maemo.org - Talk - N9 "Device not working properly"

maemo.org - Talk (https://talk.maemo.org/index.php)

- Nokia N9 / N950 (https://talk.maemo.org/forumdisplay.php?f=51)

- - N9 "Device not working properly" (https://talk.maemo.org/showthread.php?t=86708)

Re: N9 "Device not working properly"

here is the terminal output:

Code:

kristina@kristina-WIM2210:~/Desktop$ sudo su

[sudo] password for kristina:

root@kristina-WIM2210:/home/kristina/Desktop# sudo flasher --load -k vmlinuz-2.6.32.20112201-11.2-adaptation-n950-bootloader -n initrd.img-rescue-2.6.32.20112201-11.2-n950 --boot

flasher 3.12.1 (Oct  5 2011) Harmattan

WARNING: This tool is intended for professional use only. Using it may result

in permanently damaging your device or losing the warranty.



Suitable USB interface (bootloader/phonet) not found, waiting...

USB device found at bus 001, device address 003.

Device identifier: 357923045421783 (SN: N/A)

Found device RM-696, hardware revision 1603

NOLO version 2.3.6

Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_001

Sending kernel image (2497 kB)...

100% (2497 of 2497 kB, avg. 24731 kB/s)

Sending initfs image (1920 kB)...

100% (1920 of 1920 kB, avg. 23414 kB/s)

Success

root@kristina-WIM2210:/home/kristina/Desktop#

update:

so i unplugged the N9 and plugged it back in and now i am getting the old Device not working properly message

Re: N9 "Device not working properly"

the output is as expected...

Edit: so you will have to repeat the earlier steps and wait for it to get detected as removable media before proceeding with the next steps...

if it doesnt get detected after 5mins in terminal run:

Code:

fdisk -l

and paste the output here...

Re: N9 "Device not working properly"

Quote:

Originally Posted by thedead1440 (Post 1263527)

the output is as expected...

what should i do next?

Re: N9 "Device not working properly"

Quote:

Originally Posted by thedead1440 (Post 1263527)

Code:

fdisk -l

and paste the output here...

OK just did step 4, output same as last time, N9 shows a Warning and terminal says success. I'll just wait for 5 minutes.

And thank you for helping me out again :) i really appreciate it

Re: N9 "Device not working properly"

ok after fdisk -l

Code:

root@kristina-WIM2210:/home/kristina/Desktop# fdisk -l



Disk /dev/sda: 250.1 GB, 250059350016 bytes

255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors

Units = sectors of 1 * 512 = 512 bytes

Sector size (logical/physical): 512 bytes / 512 bytes

I/O size (minimum/optimal): 512 bytes / 512 bytes

Disk identifier: 0x63502bc0



   Device Boot      Start         End      Blocks   Id  System

/dev/sda1   *          63   277363613   138681775+   7  HPFS/NTFS/exFAT

/dev/sda2       277364734   488392064   105513665+   f  W95 Ext'd (LBA)

/dev/sda5       435152718   488392064    26619673+   b  W95 FAT32

/dev/sda6       277364736   428881919    75758592   83  Linux

/dev/sda7       428883968   435150847     3133440   82  Linux swap / Solaris



Partition table entries are not in disk order

root@kristina-WIM2210:/home/kristina/Desktop#

Re: N9 "Device not working properly"

your n9 is simply not being detected o.O

Let me see what could be a plausible solution for it...

Re: N9 "Device not working properly"

Quote:

Originally Posted by thedead1440 (Post 1263539)

your n9 is simply not being detected o.O

Let me see what could be a plausible solution for it...

should i just re-flash it like last time?

Re: N9 "Device not working properly"

Quote:

Originally Posted by mariusmssj (Post 1263540)

should i just re-flash it like last time?

Well that would have to be done if we can't get it detected...If you don't have much to lose from a re-flash then might as well re-flash...

Edit: There is nothing i could get on why the drives are not detected even though you get a success after entering the commands...I lose :o..A re-flash has to be done...

Re: N9 "Device not working properly"

well it's charging now battery was at 4% and then it re-flash