Page 1 of 2 1 2
Reply
Thread Tools
stc77 is offline stc77
2013-01-09 , 10:57
Posts: 3 | Thanked: 0 times | Joined on Jan 2013
#1
Dropped my N9 (PR1.3) and now the screen is broken and not usabel at all. Got a new / used N9 for less money than a replacement screen would have been. So how do I get my data off the old broken phone to the new one? Any suggestions?
Usually, if I plug the phone to an ubuntu pc, the phone asked wether to use as mass storage or something like that. But now I can not confirm that as the touch screen is not working.
I'd be very happy for any useful suggestion.
 
thedead1440 is offline thedead1440
2013-01-09 , 11:03
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#2
http://wiki.meego.com/N950/Fixing_MALF_state

Follow instructions on that wiki page till step 7 to access your full device contents...

You can use "dd" to pack your rootfs and userfs partition which you can then restore as is to your new N9 too... EMMC data of course you can transfer out and do a manual transfer into the new n9...

Using "dd" though will put your phone into open mode so if you don't want to use open mode just get your data out from the old N9 but don't use dd to transfer it into the new N9...
 

The Following User Says Thank You to thedead1440 For This Useful Post:
bvaibhav is offline bvaibhav
2013-01-09 , 11:05
Posts: 58 | Thanked: 10 times | Joined on Dec 2011
#3
JFYI...
Some time back I had similar issue with my N900, which was resolved by using rescue os.

http://talk.maemo.org/showpost.php?p...9&postcount=37
 

The Following User Says Thank You to bvaibhav For This Useful Post:
myname24 is offline myname24
2013-01-09 , 11:15
Posts: 545 | Thanked: 560 times | Joined on Dec 2011 @ lebanon
#4
I have the same issue ( and i bought a used one but in perfect condition for 100$ wich is less than repair cost ) and I tried the fixed malf but no device is being detected .( tried on ubuntu and win 7 )
 
thedead1440 is offline thedead1440
2013-01-09 , 11:23
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#5
Originally Posted by myname24 View Post
I have the same issue ( and i bought a used one but in perfect condition for 100$ wich is less than repair cost ) and I tried the fixed malf but no device is being detected .( tried on ubuntu and win 7 )
Its for Unix-based systems only so I hope you used a VM on Win7

Did you check maybe your battery was insufficient before trying the chroot?
 
myname24 is offline myname24
2013-01-09 , 11:31
Posts: 545 | Thanked: 560 times | Joined on Dec 2011 @ lebanon
#6
yes battery was dead in the beggining but I used flasher to recharge and flash it to pr 1.3 ( it was pr 1.2 ) . Now it's around 50% . From wiki the steps are done succesfully but no mass storage is detected .
 
thedead1440 is offline thedead1440
2013-01-09 , 11:34
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#7
Originally Posted by myname24 View Post
yes battery was dead in the beggining but I used flasher to recharge and flash it to pr 1.3 ( it was pr 1.2 ) . Now it's around 50% . From wiki the steps are done succesfully but no mass storage is detected .
You mean it doesn't auto-mount or there is no drive detected itself via fdisk etc?

If the former, you've to mount it then and if the latter I'm not too sure on what to do...
 
myname24 is offline myname24
2013-01-09 , 11:36
Posts: 545 | Thanked: 560 times | Joined on Dec 2011 @ lebanon
#8
Originally Posted by thedead1440 View Post
You mean it doesn't auto-mount or there is no drive detected itself via fdisk etc?

If the former, you've to mount it then and if the latter I'm not too sure on what to do...
No drive detected .
 
rainisto is offline rainisto
2013-01-09 , 12:09
Posts: 1,067 | Thanked: 2,383 times | Joined on Jan 2012 @ Finland
#9
One option is to build yourself a custom serial cable, and connect it to tx rx pins (that are under the sim card), use 115200 8n1 (non rts) as connection parameters, and do backup from commandline. (enable hardware serialport with flasher --set-rd-flags=serial-console)

Or find someone who can do it for you. ;-).

Downside to this solution is that there are not that many persons in the world that know how to do it. If your located in Finland then you might be in luck, otherwise odds are that much worse.
__________________
IRC: jonni@freenode
Sailfish: ¤ Qt5 SailfishTouchExample ¤ Qt5 MultiPointTouchArea Example ¤ ipaddress ¤ stoken ¤ Sailbox (Dropbox client) ¤
Harmattan: ¤ Presence VNC for Harmattan ¤ Live-F1 ¤ BTinput-terminal ¤ BabyLock ¤ BabyLock Trial ¤ QML TextTV ¤
Disclaimer: all my posts in this forum are personal trolling and I never post in any official capacity on behalf of any company.
 
rainisto is offline rainisto
2013-01-09 , 12:14
Posts: 1,067 | Thanked: 2,383 times | Joined on Jan 2012 @ Finland
#10
And second option, if you manage to get yourself into openmode and can mount root partition, is to make init script that installs vnc-server and you connect to it from your PC.
__________________
IRC: jonni@freenode
Sailfish: ¤ Qt5 SailfishTouchExample ¤ Qt5 MultiPointTouchArea Example ¤ ipaddress ¤ stoken ¤ Sailbox (Dropbox client) ¤
Harmattan: ¤ Presence VNC for Harmattan ¤ Live-F1 ¤ BTinput-terminal ¤ BabyLock ¤ BabyLock Trial ¤ QML TextTV ¤
Disclaimer: all my posts in this forum are personal trolling and I never post in any official capacity on behalf of any company.
 
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

 
Forum Jump


All times are GMT. The time now is 07:19.

Contact Us - Home - Archive - Top