Page 90 of 110 « First 808889 90 9192100 Last »
Closed Thread
Thread Tools
blue_led is offline blue_led
2010-05-19 , 11:30
Posts: 306 | Thanked: 566 times | Joined on Jan 2010 @ Romania
#891
because some functions of kernel seems to be in place the single problem i see is vbus power management in host mode as i see host mode depend on this
on N900 vbus power management is broken because it use another asic OUTSIDE tusb6010 for which driver is not written.
on N810 this driver work so somebody must check with a patched driver ( with removed sections of vbus power ) if any device can work without vbus.
after that we can hope n900 will do the same
vbus will and can be a future option in driver / selection mode software
few weeks ago ( beginning of march ) i tried to inject vbus & session_valid on phy asic http://talk.maemo.org/showpost.php?p...&postcount=619 ( i will post a picture with test board )
i never believe the driver and HNP can be so grossly as manual removal of device from pc
i try the same thing as egoshin ( conect / disconect from a hub ) . http://talk.maemo.org/showpost.php?p...&postcount=624 .
tight usb timings blinded me .i have no success because i did not stop ( nasty word here ) bme
Last edited by blue_led; 2010-05-19 at 15:05.
 

The Following 2 Users Say Thank You to blue_led For This Useful Post:
MohammadAG's Avatar
MohammadAG is offline MohammadAG
2010-05-19 , 18:01
Posts: 2,473 | Thanked: 12,265 times | Joined on Oct 2009 @ Jerusalem, PS/IL
#892
Applied the patches (they only seem to add a kernel message when echoing host), kernel built and flashed.
Raised power output to 5V using joerg_rw's command.
However I still can't get it to work, the flash drive gets rejected.
Code:
[ 3129.551940] kb_lock (GPIO 113) is now closed
[ 3129.716766] kb_lock (GPIO 113) is now open
[ 3163.176361] twl4030_set_host() 4030 OTG_CTRL=0x26
[ 3163.176635] twl4030_set_host() after 4030 OTG_CTRL=0x26
[ 3180.815826] usb 1-1: USB disconnect, address 5
[ 3181.091003] usb 1-1: new high speed USB device using musb_hdrc and address 6
[ 3181.240814] usb 1-1: rejected 1 configuration due to insufficient available bus power
[ 3181.240844] usb 1-1: no configuration chosen from 1 choice
 

The Following User Says Thank You to MohammadAG For This Useful Post:
joerg_rw's Avatar
joerg_rw is offline joerg_rw
2010-05-19 , 18:07
Posts: 2,222 | Thanked: 12,651 times | Joined on Mar 2010 @ SOL 3
#893
please have a close look to
http://mxr.maemo.org/fremantle/sourc...sb/musb_core.c
145 static inline int musb_verify_charger(void __iomem *addr)
ff
207

for seemingly working handling of the pullup/pulldown Rs (the MAIN most IMPORTANT config in PHY for hostmode)
__________________
Maemo Community Council member [2012-10, 2013-05, 2013-11, 2014-06 terms]
Hildon Foundation Council inaugural member.
MCe.V. foundation member

EX Hildon Foundation approved Maemo Administration Coordinator (stepped down due to bullying 2014-04-05)
aka "techstaff" - the guys who keep your infra running - Devotion to Duty http://xkcd.com/705/

IRC(freenode): DocScrutinizer*
First USB hostmode fanatic, father of H-E-N
 

The Following 2 Users Say Thank You to joerg_rw For This Useful Post:
joerg_rw's Avatar
joerg_rw is offline joerg_rw
2010-05-19 , 18:15
Posts: 2,222 | Thanked: 12,651 times | Joined on Mar 2010 @ SOL 3
#894
Originally Posted by MohammadAG View Post
Applied the patches (they only seem to add a kernel message when echoing host), kernel built and flashed.
Raised power output to 5V using joerg_rw's command.
However I still can't get it to work, the flash drive gets rejected.
[code][ 3129.551940] kb_lock (GPIO 113) is now closed
[ 3129.716766] kb_lock (GPIO 113) is now open
[ 3163.176361] twl4030_set_host() 4030 OTG_CTRL=0x26
[ 3163.176635] twl4030_set_host() after 4030 OTG_CTRL=0x26
[ 3180.815826] usb 1-1: USB disconnect, address 5
[ 3181.091003] usb 1-1: new high speed USB device using musb_hdrc and address 6
[ 3181.240814] usb 1-1: rejected 1 configuration due to insufficient available bus power
[ 3181.240844] usb 1-1: no configuration chosen from 1 choice
please see
61 * HP's USB bus-powered keyboard has only one configuration
ff
in http://mxr.maemo.org/fremantle/sourc...core/generic.c
Code:
61                  * HP's USB bus-powered keyboard has only one configuration
62                  * and it claims to be self-powered; other devices may have
63                  * similar errors in their descriptors.  If the next test
Code:
135         if (insufficient_power > 0)
136                 dev_info(&udev->dev, "rejected %d configuration%s "
137                         "due to insufficient available bus power\n",
138                         insufficient_power, plural(insufficient_power));


[edit]
ok, seems we killed that issue by patching out a few rather useless checks in kernel. Probably MohammadAG will come up with a small and dirty patch eventually. No big thing though. Still the fake hostmode by tricking OTG statemachine, I.E needs laptop to simulate the yet missing switch of PHY to host config (2 pulldowns)
__________________
Maemo Community Council member [2012-10, 2013-05, 2013-11, 2014-06 terms]
Hildon Foundation Council inaugural member.
MCe.V. foundation member

EX Hildon Foundation approved Maemo Administration Coordinator (stepped down due to bullying 2014-04-05)
aka "techstaff" - the guys who keep your infra running - Devotion to Duty http://xkcd.com/705/

IRC(freenode): DocScrutinizer*
First USB hostmode fanatic, father of H-E-N
Last edited by joerg_rw; 2010-05-19 at 23:32.
 

The Following 5 Users Say Thank You to joerg_rw For This Useful Post:
hcm is offline hcm
2010-05-19 , 22:09
Posts: 75 | Thanked: 78 times | Joined on Jan 2010 @ Germany
#895
guys, I have some news about bme's i2c communication with bq24150.
Be aware that this is ALL communication to bq24150 through the kernel. Not necessarily only by BME.

initialisation (contains some nonsense IMHO):
Code:
i2c-2 (W): 0x3b, (R) 1 bytes, 	// read register 0x3b (wraps to 0x03, datasheet states otherwise!)
i2c_read:  0x4b			// result: Vendor/Part/Revision
i2c-2 (W): 0x3b, (R) 1 bytes,	// same
i2c_read:  0x4b
i2c-2 (W): 0x00, (R) 1 bytes,	// read status/control register
i2c_read:  0x00			// reset state should be x1xx 0xxx (datasheet)
i2c-2 (W): 0x00 0x80,		// reset safety timer
i2c-2 (W): 0x02, (R) 1 bytes,	// read control/battery register
i2c_read:  0x8c			// 3.5V + 700mV
i2c-2 (W): 0x02 0x8c,		// set control/battery to same value
i2c-2 (W): 0x00, (R) 1 bytes,	// read status
i2c_read:  0x00
i2c-2 (W): 0x00 0x00,		// write status
i2c-2 (W): 0x01, (R) 1 bytes,	// read control register
i2c_read:  0x06			// charger disabled, high impedance
i2c-2 (W): 0x01 0x06,		// set to same value
i2c-2 (W): 0x00, (R) 1 bytes,	// read status
i2c_read:  0x00
i2c-2 (W): 0x01, (R) 1 bytes,	// read control register
i2c_read:  0x06			// same as above
i2c-2 (W): 0x01 0x06,		// set to same value again
i2c-2 (W): 0x01, (R) 1 bytes,	// read again
i2c_read:  0x06
i2c-2 (W): 0x01 0x06,		// write again
every 15s:
Code:
i2c-2 (W): 0x00 0x80,		// reset safety timer
i2c-2 (W): 0x00, (R) 1 bytes,	// read status
i2c_read:  0x00
i2c-2 (W): 0x02, (R) 1 bytes,	// read control/battery register
i2c_read:  0x8c
i2c-2 (W): 0x04, (R) 1 bytes,	// read battery termination/fast charge current register
i2c_read:  0xca			// charge current sense voltage = 27.2mV
				// termination current sense voltage = 6.8mV
nothing too special, yet. But the printk's can be usefull when trying to find out how BME destroys VBUS, etc…

The diff for my printk's are attached.
Attached Files
File Type: txt bq24150-sniff.patch.txt (1.3 KB, 143 views)
 

The Following 4 Users Say Thank You to hcm For This Useful Post:
blue_led is offline blue_led
2010-05-19 , 22:24
Posts: 306 | Thanked: 566 times | Joined on Jan 2010 @ Romania
#896
those messages are obtained with high power charger attached , right ?
so nothing special , bme reset 32 s timer 4 times per minute . too often i think but in charge mode any battery savings is nonsense.
bme don't destroy vbus , simply bme have no idea ( and code ) about vbus and host mode status.
code is written only for charging mode not charge or boost vbus
Last edited by blue_led; 2010-05-19 at 22:32.
 

The Following User Says Thank You to blue_led For This Useful Post:
blue_led is offline blue_led
2010-05-19 , 22:28
Posts: 306 | Thanked: 566 times | Joined on Jan 2010 @ Romania
#897
Originally Posted by MohammadAG View Post
Applied the patches (they only seem to add a kernel message when echoing host), kernel built and flashed.
Raised power output to 5V using joerg_rw's command.
However I still can't get it to work, the flash drive gets rejected.
Code:
[ 3129.551940] kb_lock (GPIO 113) is now closed
[ 3129.716766] kb_lock (GPIO 113) is now open
[ 3163.176361] twl4030_set_host() 4030 OTG_CTRL=0x26
[ 3163.176635] twl4030_set_host() after 4030 OTG_CTRL=0x26
[ 3180.815826] usb 1-1: USB disconnect, address 5
[ 3181.091003] usb 1-1: new high speed USB device using musb_hdrc and address 6
[ 3181.240814] usb 1-1: rejected 1 configuration due to insufficient available bus power
[ 3181.240844] usb 1-1: no configuration chosen from 1 choice
try with a minimum 100 uF capacitor on vbus to avoid vbus drop ( early host specs don't throw with tomato )
681 if (int_usb & MUSB_INTR_VBUSERROR) {
682 int ignore = 0;
683
684 /* During connection as an A-Device, we may see a short
685 * current spikes causing voltage drop, because of cable
686 * and peripheral capacitance combined with vbus draw.
687 * (So: less common with truly self-powered devices, where
688 * vbus doesn't act like a power supply.)
689 *
690 * Such spikes are short; usually less than ~500 usec, max
691 * of ~2 msec. That is, they're not sustained overcurrent
692 * errors, though they're reported using VBUSERROR irqs.
693 *
694 * Workarounds: (a) hardware: use self powered devices.
695 * (b) software: ignore non-repeated VBUS errors.
696 *
697 * REVISIT: do delays from lots of DEBUG_KERNEL checks
698 * make trouble here, keeping VBUS < 4.4V ?
699 */
700 switch (musb->xceiv->state) {
701 case OTG_STATE_A_HOST:
702 /* recovery is dicey once we've gotten past the
703 * initial stages of enumeration, but if VBUS
704 * stayed ok at the other end of the link, and
705 * another reset is due (at least for high speed,
706 * to redo the chirp etc), it might work OK...
707 */
Last edited by blue_led; 2010-05-19 at 22:30.
 

The Following User Says Thank You to blue_led For This Useful Post:
Dollyknot is offline Dollyknot
2010-05-19 , 22:51
Posts: 92 | Thanked: 13 times | Joined on Nov 2009 @ leicester UK
#898
We might want to operate hostmode without burning battery for VBUS boost, by using an externally powered hub.

Yeah we want to give our baby more energy, not take energy from it.


04-26-10 , 01:47 PM
Posts: 82 | Thanked: 9 times | Joined on Nov 2009 @ leicester UK

Report This | #1
Someone on one of the forums mentioned that the 'Memorex Travellink' could be used to transfer files from the n900 to a USB memory stick so I bought one.

Needless to say it did not work first time, but I thought it was still worth it because I could read and copy the SD card with it, so it would still be usable when I start travelling later on in the year.

Somebody posted an app to mount an exterior partition, so I downloaded it, plugged a USB stick into the Travellink and the n900 USB link 'coz I thought I could mount the stick with the downloaded app.

Much to my pleasant surprise, the Travellink was able to see files on my n900 and transfer them to my USB memory stick without the use of a PC or laptop, also it not did not need the mounter wizard.

What might have happened the first time is, I tried to do it without a fully charged battery, this time I tried with a fully charged battery, the perfect accessory for the traveller who wants to shoot lots of videos and store them on the road without carrying lots of kit.

The Travellink runs on three AA batteries, which I would imagine can be bought all over the planet.
Last edited by Dollyknot; 2010-05-19 at 23:36. Reason: bit waste.
 
MohammadAG's Avatar
MohammadAG is offline MohammadAG
2010-05-19 , 23:25
Posts: 2,473 | Thanked: 12,265 times | Joined on Oct 2009 @ Jerusalem, PS/IL
#899
Compiled a kernel that works (finally! - thanks to joerg_rw for pointing out how to stop any power limits - my flash apparently needs more power).
I'll post a patch shortly.

I also got an HDD working, using the laptop as a power source, and without any "real" hub in between (using a Y cable though).

The echo host > ... part is redundant and doesn't do anything, so it can be left out.
Not sure about the patches, but it seems they only add messages to the kernel messages. Also I had to edit the .config file directly not the one in arch/arm/configs, since that didn't change anything (thanks to javispedro for that one)

Code:
[ 1617.796691] g_nokia gadget: high speed config #1: nokia1
[ 1617.796783] musb_hdrc periph: enabled ep5in for int IN, maxpacket 10
[ 1617.796783] musb_hdrc periph: enabled ep4in for bulk IN, maxpacket 512
[ 1617.796813] musb_hdrc periph: enabled ep4out for bulk OUT, maxpacket 512
[ 1617.796905] musb_hdrc periph: enabled ep7in for int IN, maxpacket 16
[ 1617.824737] musb_hdrc periph: enabled ep6in for bulk IN, maxpacket 512
[ 1617.824768] musb_hdrc periph: enabled ep5out for bulk OUT, maxpacket 512
[ 1619.233032] hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
[ 1619.233093] hub 1-0:1.0: unable to enumerate USB device on port 1
# Was experimenting with something, ignore the 2 errors above ^
[ 1645.303344] usb 1-1: new high speed USB device using musb_hdrc and address 12
[ 1645.453826] usb 1-1: configuration #1 chosen from 1 choice
[ 1645.551605] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1645.590362] usb-storage: device found at 12
[ 1645.590393] usb-storage: waiting for device to settle before scanning
[ 1645.838378] input: Western Digital  External HDD     as /class/input/input4
# No idea what this ^ is for, SpeedEvil suggested it could be for the LEDs on the drive.
[ 1645.892456] generic-usb 0003:1058:0705.0001: input: USB HID v1.10 Device [Western Digital  External HDD    ] on usb-musb_hdrc-1/input1
[ 1645.893554] usbcore: registered new interface driver usbhid
[ 1645.893615] usbhid: v2.6:USB HID core driver
[ 1650.585540] usb-storage: device scan complete
[ 1650.586639] scsi 2:0:0:0: Direct-Access     WD       3200BEV External 1.75 PQ: 0 ANSI: 0
[ 1650.619903] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 1650.620391] sd 2:0:0:0: [sda] Write Protect is off
[ 1650.620422] sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 1650.620422] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 1650.621154] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 1650.621551] sd 2:0:0:0: [sda] Write Protect is off
[ 1650.621582] sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 1650.621582] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 1650.621612]  sda: sda1
[ 1650.672180] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2936.905181] usb 1-1: USB disconnect, address 12
[ 2937.256347] usb 1-1: new high speed USB device using musb_hdrc and address 13
[ 2937.405853] usb 1-1: configuration #1 chosen from 1 choice
[ 2937.405883] usb 1-1: new config #1 exceeds power limit by 100mA
[ 2937.435028] scsi3 : SCSI emulation for USB Mass Storage devices
[ 2937.473449] usb 1-1: 200mA is over 100mA budget for port 1!
[ 2937.473480] hub 1-0:1.0: 100mA over power budget!
[ 2937.476623] usb-storage: device found at 13
[ 2937.476623] usb-storage: waiting for device to settle before scanning
[ 2942.476196] usb-storage: device scan complete
[ 2942.477081] scsi 3:0:0:0: Direct-Access     SanDisk  U3 Contour       4.04 PQ: 0 ANSI: 2
[ 2942.477539] scsi 3:0:0:1: CD-ROM            SanDisk  U3 Contour       4.04 PQ: 0 ANSI: 2
# U3 enabled flash drive, the CD-ROM is emulated by the flash drive, it's not an actual CD-ROM, mind you a CD drive might be used with a self powered hub.
[ 2942.510925] sd 3:0:0:0: [sda] 16041617 512-byte hardware sectors: (8.21 GB/7.64 GiB)
[ 2942.511383] sd 3:0:0:0: [sda] Write Protect is off
[ 2942.511413] sd 3:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 2942.511413] sd 3:0:0:0: [sda] Assuming drive cache: write through
[ 2942.516235] sd 3:0:0:0: [sda] 16041617 512-byte hardware sectors: (8.21 GB/7.64 GiB)
[ 2942.516540] sd 3:0:0:0: [sda] Write Protect is off
[ 2942.516540] sd 3:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 2942.516571] sd 3:0:0:0: [sda] Assuming drive cache: write through
[ 2942.516601]  sda: sda1
[ 2942.530303] sd 3:0:0:0: [sda] Attached SCSI removable disk
Making the drive appear in file manager is **** easy, just create a directory in /media and mount the drive/flash to it.





Last edited by MohammadAG; 2010-05-20 at 10:55. Reason: Added my comments to the message kernels
 

The Following 26 Users Say Thank You to MohammadAG For This Useful Post:
egoshin is offline egoshin
2010-05-20 , 00:48
Posts: 992 | Thanked: 995 times | Joined on Dec 2009 @ California
#900
Originally Posted by MohammadAG View Post
[ 1645.838378] input: Western Digital External HDD as /class/input/input4
# No idea what this is ^ is for, SpeedEvil suggested it could be for the LEDs on the drive.
It is a CPU frequency boost on any event from your WD HD.
 
Closed Thread
Page 90 of 110 « First 808889 90 9192100 Last »

Tags
awesomeness in the works, boulevard of broken deals, host, i am the dealbreaker, inspector gadget lies, mobidapter is a scam, nokia fanbois, otg, over 9000, usb, usbcontrol

« Previous Thread | Next Thread »

 
Forum Jump


All times are GMT. The time now is 10:43.

Contact Us - Home - Archive - Top